Two strain gauges with a gauge factor K (which will be the last 2 digits of your student number) are placedon the chest and belly (diaphragm) area of a subject as shown in below figure. The gauges have an initialresistance of 1000 and they are connected to the given Wheatstone Bridge circuit. And output ofWheatstone Bridge circuit is connected to an instrumentation amplifier as shown in below figure. Thegauges measures the extension of chest and belly according to respiration. The resistance values foramplifier is given below.Rs = R, = R4 = 1kN, R. = 1000, Rp = 5000 , Vcc = 5VWhen the subject exhaled the strain gauges are relaxed and when the subject inhaled strain gauge A isstretched 1% and B is stretched 2%. Answer the below questions when the subject is inhaled.21- What will be the resistance value in the strain gauge A, RA ?22- What will be the resistance value in the strain gauge B, Rs ?23- What will be the voltage difference Vg-VA ?24- What will be the amplifier output Vo1 ?StrainGauge AStrainGauge BR2R4VA1RARsRCVoiRpVccRBRORsR2R4VB23.

1. Consider your roll number the last digit to be 02. The value of change is resistance is given…

Two strain gauges with a gauge factor K (which will be the last 2 digits of your student number) are placed on the chest and belly (diaphragm) area of a subject as shown in below figure. The gauges have an initial resistance of 1000 and they are connected to the given Wheatstone Bridge circuit. And output of Wheatstone Bridge circuit is connected to an instrumentation amplifier as shown in below figure. The gauges measures the extension of chest and belly according to respiration. The resistance values for amplifier is given below. Rs = R2 = R4 = 1kN, R. = 1000, Rp = 5000, Vcc = 5V When the subject exhaled the strain gauges are relaxed and when the subject inhaled strain gauge A is stretched 1% and B is stretched 2%. Answer the below questions when the subject is inhaled. 21- What will be the resistance value in the strain gauge A, RA ? 22- What will be the resistance value in the strain gauge B, Rs ? 23- What will be the voltage difference Va-Va ? 24- What will be the amplifier output Vo1 ? Strain Gauge A Strain Gauge B R2 R4 VA RA Rs RC Voi Rp Vcc RB RC Rs R2 R4 VB 2

Two strain gauges with a gauge factor K (which will be the last 2 digits of your student number) are placed on the chest and belly (diaphragm) area of a subject as shown in below figure. The gauges have an initial resistance of 1000 and they are connected to the given Wheatstone Bridge circuit. And output of Wheatstone Bridge circuit is connected to an instrumentation amplifier as shown in below figure. The gauges measures the extension of chest and belly according to respiration. The resistance values for amplifier is given below. Rs = R2 = R4 = 1kN, R. = 1000, Rp = 5000, Vcc = 5V When the subject exhaled the strain gauges are relaxed and when the subject inhaled strain gauge A is stretched 1% and B is stretched 2%. Answer the below questions when the subject is inhaled. 21- What will be the resistance value in the strain gauge A, RA ? 22- What will be the resistance value in the strain gauge B, Rs ? 23- What will be the voltage difference Va-Va ? 24- What will be the amplifier output Vo1 ? Strain Gauge A Strain Gauge B R2 R4 VA RA Rs RC Voi Rp Vcc RB RC Rs R2 R4 VB 2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Let's assume that 0V when A, B, C, D, E switches are open and 1V when they are closed. What will be the V0 output voltage value when the switches are closed in the order in the table? According to this, draw the shape of the A, B, C, D, E and V0 voltages. Comment on how the circuit turned out. Opamp's supply is ± 12V
You are an electrician working on an overhead crane. The crane uses a large electromagnet to pick up large metal pipes. The magnet must have a minimum of 200 VDC to operate properly. The crane has an AC source of 240 V. You are given four diodes that have a peak voltage rating of 400 V each. These diodes are to be used to form a bridge rectifier to convert the AC voltage into DC voltage. Is the voltage rating of the diodes sufficient? To the nearest volt, what will be the DC output voltage of the bridge rectifier?
c) The following stiff voltage-divider circuit in Figure Q2 (c) consists of BJT with DC gain 140. Determine Q-point if Vcc= 12V, R1=15kO, R2 =5.6kn, RĘ =6000 and Rc=1.0kO. R, R. Vcc R2 RE ww ww w- ww
Q3
Plz solve all parts , i vll upvote and share positive feedback ...... ASAP PLZZZ
ans fast please
In Full Bridge arrangement of strain measurement, supply voltage is of 0.5 V and resistance of each arm is 190 ohms. The change in resistance will be 24 ohms and the gauge factor will be 0.5. Find a) output voltage in mV b) strain output voltage in mV Strain
Sketch the output voltage waveform for each op armp circuits given below. Given the maximum outputvoltage for the op-armp is Vomax = +10 v and Vomin = -10 v.Use input voltage for all circuit as shown. Also use V2 = 4.7 V for D1 and D2. V. 0 -5V- -5V D1 Kt 1K 1K D2 V1 V2
ans fast please
... .. 0 O .. . . .O .. . e A student intends to connect a TL082 OP-AMP as a voltage follower, to "follow" the voltage generated by a potentiometer but makes some mistakes in the breadboard wiring: *He took Pin 3 and connected it to Pin 1, but this is wrong as Pin 3 is supposed to go to Pin 6, fix this. *A meter lead is supposed to go to Pin 6, the output not to Pin 1. A 3rd mistake results in no output but this he cannot discover, help him. Sketch a schematic diagram of this circuit, fixing the above (don't forget to include the Voltmeter) and determine what the voltmeter's indication will be, explaining why it is such. 12 V TL082 12 V AA OFF COM
You are an electrician working on an overhead crane. The crane uses a large electromagnet to pick up large metal pipes. The magnet must have a minimum of 200 VDC to operate properly. The crane has an AC source of 240 V. You are given four diodes that have a peak voltage rating of 400 V each. These diodes are to be used to form a bridge rectifier to convert the AC voltage into DC voltage. Is the voltage rating of the diodes sufficient? To the nearest volt, what will be the DC output voltage of the bridge rectifier?
4. The unbonded strain gauge accelerometer of Figure P4 natural frequency of 175 Hz and an input range of 0 to 5g. Given that the stra in due to pre-stressing is twice the maximum has a acceleration-induced strain, use the strain gauge data of Table P4 to calculate the range of the bridge output voltage*. Table P4: Data for Problem 4 Resistance = 120 Q Gauge factor =2.1 Maximum current (through any gauge)= 50 mA Length at zero acceleration =2.3 cm Acceleration due to gravity, g =9.81 m s? %3D 2 1 eo - e en +e m 4 eo - e eo +e