TWO SOLID CYLINDRICAL RODS ARE JOINED AT B AND LOADED AS SHOWN. ROD AB IS MADE OF STEEL (E = 210 GPa) AND ROD BC OF BRASS (E = 108 GPa). DETERMINE (A) THE TOTAL DEFORMATION OF THE COMPOSITE ROD ABC, (B) THE DEFLECTION OF POINT B. 40 KN

TWO SOLID CYLINDRICAL RODS ARE JOINED AT B AND LOADED AS SHOWN. ROD AB IS MADE OF STEEL (E = 210 GPa) AND ROD BC OF BRASS (E = 108 GPa). DETERMINE (A) THE TOTAL DEFORMATION OF THE COMPOSITE ROD ABC, (B) THE DEFLECTION OF POINT B. 40 KN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The aluminum rod AB (G = 27 GPa) is bonded to the brass rod BD (G = 39 GPa). Knowing that portion CD of the brass rod is hollow and has an inner diameter of 40 mm, determine the angle of twist at A. 60 mm Tg = 1S00 N- m 40 mm TA = 600 N - m 250 mm 375 mm A 400 mm
The rigid bar ABCD supports point loads at A and D and is being supported by two bars at B and C. Determine the absolute value of the deformation at point C. (in mm) 120KN 4m Sm A B L= 6m 9o kN L-4m A= 0.04 m A = 0.0 6m² E=200 GAa E=80 GPa
Value of P1=9 kNP2=105 kNP3=89 kNd=159 mm Strength of Materials
The rigid bar AB, attached to two vertical rods as shown in Fig. is horizontalbefore the load P is applied. Determine the maximum value for P If the stress must not exceed: 160 MPa for steel and 80 MPa for Bronze. Then determine the vertical movement of P. STEEL Lm A-400 mm E-200 GPa BRONZE L-5m A-500 mm E-80 GPa 3m
3) The rigid link is supported by steel wire (1) with an unstretched length of 200 mm and cross-sectional area of 22.5 mm?. Member (2) is a short aluminum of initial length 50 mm and cross-sectional area of 40 mm?. The modulus of elasticity of the steel wire is 200 GPa and the aluminum block is 70 GPa. a) Draw the deflected shape of the rigid member and clearly label the deformation of members (1) and (2). b) Write the equilibrium and compatibility equations needed to solve the problem along with the supporting sketches. Hint: Be sure to carefully consider if the members are elongating or shortening; this must be represented mathematically. c) Calculate the internal forces in both axial members and clearly indicate tension or compression. [Ans. to Check: F2 = 535 N]
The rigid bar ABCD supports point loads at A and D and is being supported by two bars at B and C. Determine the absolute value of the deformation at point C. (in mm) 120KN 4m 3m Sm A L= 6m 90 kN L-4m A= 0.04m A = 0.0 Gm² E=200 GA E=80 GPa
The rigid bar ABCD supports point loads at A and D and is being supported by two bars at B and C. Determine the absolute value of the deformation at point C. (in mm) 120KN 4m 3m Sm A 90 kN L3 6m A= 0.04 m A = 0.06m² E=200 6AE=80 GPa L-4m
Two solid cylindrical rods are joined at B and loaded asshown. Rod AB is made of steel (E = 200 GPa) and rod BCof brass (E = 105 GPa). Determinea. the deformation of rod ABb. the deformation of rod BCc. the total deformation of the composite rod ABCd. the deflection of point B.
The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and has a cross sectional area of 500 mm^2. Link CD made of steel (E = 200 GPa) and has a cross sectional area of 600 mm^2. Determine the deflection at D in mm
The brass rod AB is fixed connected at A. When the temperature is T₁-50 °C, there is a 3 mm gap between its end (point B) and the wall C. The cross-sectional area of the rod is 10 cm². Ignore the weight of the bar. The temperature is now increased to T₂-130 °C and the rod AB is pushing against the wall at C. Ebr = 100 GPa, abr = 20 x 10-6/°C Fallow 70 MPa L = 3m A 3 m B/C с 3 mm a. Draw a FBD for when the temperature is increased to T₂ and write down the force balance for this scenario. Call the reactions at FA and FC. Ton =1) und prit brolim volgen Aistis Intelesa si s b. State the compatibility condition and solve for the reactions at A and C.
4
The rigid bar AC is supported by two axial bars (1) and (2). Both axial bars are made of bronze [E = 100 GPa; a = 18 x 10-6 mm/mm/ °C). The cross-sectional area of bar (1) is A, = 184 mm2 and the cross-sectional area of bar (2) is A2 = 380 mm2. After load P has been applied and the temperature of the entire assembly has increased by 38°C, the total strain in bar (2) is measured as 1240 µɛ (elongation). Assume L1 = 1290 mm, a = 590 mm, b = 820 mm, and L2 = 2000 mm. Determine: (a) the magnitude of load P. (b) the vertical displacement of pin A. (2) L2 |(1) L1 В a Answers: (a) The magnitude of P = i kN. (b) The vertical displacement of pin A = i mm (down).