Two rectangular tanks, A and B, are filled to a height, ha and hb respectively, as shown; ha is double hb, the width of container B is double that of A, and the containers have the same wall thickness. How does the pressure and the force at the bottom of the tanks compare, respectively? You may assume the length of each container is equal.

Two rectangular tanks, A and B, are filled to a height, ha and hb respectively, as shown; ha is double hb, the width of container B is double that of A, and the containers have the same wall thickness. How does the pressure and the force at the bottom of the tanks compare, respectively? You may assume the length of each container is equal.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two semi-spherical thin-walled vessels are joined together by attaching 40-mm bolts around the circumference to form a spherical vessel which can carry a pressure of 3 MPa. If the internal diameter of the vessel is 2 m and the allowable stress in the bolts is 70 MPa, how many bolts must be used ? (answer in whole number) Round your answer to 0 decimal places. Add your answer
DESIGN DESCRIPTION To construct a warehouse, the frame system shown in Figure 1 has been adopted. As an engineer, your task is to analyse the mid frame, highlighted in RED. Column 3 Column 1 Beam 1 Columb 2 Slab 1 Beam 1 Slab 2 Beam 2 Beam 3 Column 2 5 m 5 m 5 m Column 3 Column 1 8 m (a) Transfer of self-weight of Slabs 1 and 2 to surrounding beams (simplified case) Beam 1 Figure 1 A warehouse frame system The detailed information of the structural components is provided as follows: Slabs 1 and 2 are made of in-situ cast reinforced concrete and have a thickness of 150 mm (Figure 2). For simplicity, we assume that half the weight of each slab is transferred to Beam 1 (as shown in Figure 2). In addition, a water tank full of water with a weight of 1042 kg (1000 L of water plus weight of the tank) will be installed in the middle of Beam 1 (Figure 2). All the beams are made of reinforced concrete and have a standard size of 225 mm x 600 mm. Note that the density of reinforced concrete is…
Quick
Please be clear with your solution. Write an explanation for the formula and solution you used.
A cylindrical rod having a diameter of 0.5in is subjected to tension. How much load is required to cause a 10-4in change in the diameter. Take Young’s modulus of rod as 11x106 psi and Poisson’s ratio as 0.33.
calculate the support reaction and show your complete solution. thank you
Determine the mass moment of inertia of the figure shown about the x,y, and z axis. The materials weighs 60 kN/m³.
(a) A wooden block of specific gravity 0.75 floats in water. If the size of the block is 1 mt x 0.5 mt x 0.4 mt, find its metacentric height.
Problem 1: Load P 24 kips compressing the concrete cylinder which length is reduced from 12 inches to 11.9970 inches after compression. The diameter increased from 6 inches to 6.003 in. Determine the value of the modulus elasticity E. = 12 in. de = 6 in -
figure below shows the proposed design for a hydraulic press used to compact solid waste. A piston at the right is capable of exerting a force of 12500 lb through connecting rod to the ram. The rod is straight and centrally loaded. it is made from AISI 1040 OQT 1100 steel (Sy=80x10^3 psi, E=30x10^6psi. compute the resulting design factor for this design. specify the required diameter of the connecting rod if it is made as a solid circular cross section. Use design factor of 4.0. ompute the resulting design factor 101 Solid waste to be compacted Emn A Ram Weld A-18m² I= 4.5int Connecting rod 12.75 ft Pin A 2.00 in Section A-A Piston 3.00 in 12 500 lb I= //12 H=4 n=0.
Problem 7: Inputs: ● ● ● ● F₁ = 9 KN F₂= 2 KN 0 = 30° a = 3 m b=1m At what distance "d" must the resultant force be located in order for the two systems to be equivalent? a F₁ d F₂ R
A cast-iron cannonball is found by a diver on the bottom of a harbor (SG of harbor water = 1.02) . The cannonball has a volume of 0.1 ft3 . The cast-iron has a specific gravity of 7.40. What force (F) is necessary to lift the cannonball off the bottom (find F in lb)? (use specific weight of water = 62.4 lb/ft3 )