Two pipes 1 and 2 having the same length and diameter are in parallel. If the flow in pipe 1 is 750 liters per second, what is the flow in pipe 2 if the friction factor f of the second pipe is twice that of the first pipe? Select one: O a. 680 liters per second O b. 530 liters per second O c. 560 liters per second O d. 620 liters per second

Two pipes 1 and 2 having the same length and diameter are in parallel. If the flow in pipe 1 is 750 liters per second, what is the flow in pipe 2 if the friction factor f of the second pipe is twice that of the first pipe? Select one: O a. 680 liters per second O b. 530 liters per second O c. 560 liters per second O d. 620 liters per second

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

AAAAAAAAAAAAAAAAAAAA 2 Pa oil with density 706kgf/" and viscosity 4-7×10 7³9 flows out of storage tank below: Determine the minimum diameter that results in a flow rate of 18 litres per minute. Provide answer in cm H = 1.4m L = 7m
The Venturi meter shown in the sketch below, contracts the flow down to one quarter of its original area. Cold air at 0 deg C flows in the pipe through the Venturi meter. The velocity of the air upstream of the Venturi meter is equal to 40 ft/s and the pressure at the same point is equal to 30 psia. What is the manometer reading if the fluid of the manometer is water with density 1000 kg/m3 . Assume that the air behaves as an ideal gas with molecular weight equal to Mw=29 kg/kmol and constant density evaluated at upstream conditions. Use Bernoulli's equation for your calculations. please respond asap!
please solve in 40 mins i need help i will give you positive feedback
How to solve this question . Step-by step solution needed with explanation. ( Fill in the Blank)
Paint issues from the tank at a flow rate of 45 ft^3/s. Find the kinetic viscosity in ft^2/s. Assume the flow is laminar. Note: In answering the question, it must be in exponential form but in the text box just write the value no need to include the x10^-1.. A 9 ft L = 6 ft d = 1/2 in ܪ e
The discharge through a 75mm diameter orifice at the bottom of an open cylindrical tank was measured to be 1930 liter per minute. If the water level inside the tank is constant at 6m, determine the coefficient of discharge. (A) No Answer among the choices B) 0.623 0.671 (D 0.718 E) 0.741
A 40-m-long, 12-mm-diameter pipe with a friction factor of 0.026 is used to siphon 30 °C water from a tank as shown in the figure below. Determine the maximum value of h allowed if there is to be no cavitation within the hose. Neglect minor losses. Use Physicala Properties of Water (SI Units
In the illustration: A 1 В 2 D All friction factor f = 0.02 All pipe lengths L - 250m Diameter of Pipe A = 400mm with Flow Rate at Pipe A= 700 L/s Diameter of Pipe B = 300mm Diameter of Pipe C = 200mm Diameter of Pipe D = 400mm Solve for - flowrate at Pipe C in Liters per second.
The water surface shown below is 10 m above the datum. The pipe is 425 mm in diameter and the total loss of head between point (1) in the water surface and point (5) in the jet is 3 m. Determine the discharge Q. (m3/s). Round your answers in 3 decimal places.
A nozzle of inner radius 1.04 mm is connected to a hose of inner radius 8.83 mm. The nozzle shoots out water moving at 25.0 m/s. 1. Required information At what speed is the water in the hose moving? cm/s Required information What is the mass flow rate? g/s 2.
Solve the following problem.
Three pipes are connected in parallel, The difference in heads in each pipe is 40 m. Pipes Diameter (cm) Length (m) Friction factor 1 15 500 0,02 2 10 450 0.03 3 20 800 0,025 3. Determine the flow in pipe 3.