Two loads P1 and P2 resting on two inclined plane and connected by a horizontal chord AB as shown in figure. If P2 = 1200 kN determine the maximum and minimum value of P1 and tension in chord AB so that the static equilibrium exist the angle of limiting friction is 23o at all rubbing surfaces.

Q: The light boom AB is attached to a vertical wall by a ball and socket joint at A and supported by…

A:

Q: Q) The ladder as shown in figure (2) has a long 15 ft and weighs 50 b. It rests against a vertical…

A:

Q: The light boom AB is attached to a vertical wall by a ball and socket joint at A and supported by…

A: Given data:- The force P is P→=20i^-10j^ kN.

Q: |Can the system in Figure (4) be in static equilibrium in the position shown? The uniform bar AB…

A:

Q: Determine the value offorce Pand F acting along the bars maintaining equilibrium of pin A. ans.: P =…

A:

Q: 4. In figure shown, two blocks are connected by a solid strut attached to each block with…

A:

Q: The frame shown is loaded by a 180-lb force applied to member AE. Determine the force at pin A, the…

A: In this question at first, two distinct Free body diagram is drawn and then with the help of static…

Q: Q4/From the figure below, ,if the mass of box is 10 kg, the coefficient of friction u=0.4. Draw the…

A:

Q: Determine whether the block shown below is in equilibrium, and find the magnitude and direction of…

A: Given:  The coefficient of static friction is μs=0.30,  The coefficient of kinetic friction is…

Q: A cylinder with a radius of 1.5 m and a weight of 40 kN is held by the rod AD. Find the force at CD…

A: The free-body diagram of the cylinder Applying equilibrium conditions: ∑Fy=0REcos300-40=0RE=46.188…

Q: Find the force in member BC, BE, and EF of the truss and state if the members are in Tension or…

A:

Q: Calculate the magnitude of the tension T and the angle 0 for which the eye bolt will be under a…

A:

Q: ne uniform 18kg Bar OA is held in the position shown by a smooth pin at O, and the cable AB which is…

A: givenuniform bar AO mass, m=18kgangle maked by bar AO with horizontal axis,θ=600length of the bar…

Q: 3- Can the system in figure be in static equilibrium in the position shown? The uniform bar AB…

A:

Q: The homogeneous 300-kg cylinder is pulled over the 100-mm step by the horizontal force P. Find the…

A: for un-equilibrium conditions the moment due to the force P about the pivot should be greater than…

Q: A body of weight N is lying on not a smooth plane inclined at an angle of 31° with the parallel. It…

A:

Q: Determine the forces in members DE and DL. The forces are positive if in tension, negative if in…

A:

Q: Please plot the FBDs that allow you to find the weight of block D to keep the whole system in…

A:

Q: Q3: The man is applying a force of 100N to the box. A mass of 300N is placed on an inclined plane as…

A:

Q: A filled barrel has dimensions of a = 0.55m, b = 1.1m, and c = 0.6m, a total mass of 108kg, and has…

A:

Q: PROBLEM 1: Consider the truss system to the right. All members are two force members. There is a pin…

A:

Q: T1 40° 75% pivot/hinge A vertical 200 kg board is held stationary by two lightweight ropes and a…

A:

Q: D. C E. L, y= B L, w Find the magnitude of the horizontal and vertical components of the pin…

A:

Q: 5-5.15. Find the couple applied to the cylinder of Prob. 5-5.14 that start counterclockwise…

A: As per Expert Guidelines, we are supposed to answer only the Question of the given multiple…

Q: The uniform blocks A and B weigh 90lb and 60lb, respectively. The coefficients of static friction at…

A: Consider the ground(the grey surface) as surface CFrom the FBD of body A We know, NAB=NBA=49.09 lb…

Q: A uniform ladder 5 m long and weighing 80N rests against on a vertical wall at B and one end at A…

A:

Q: 30 in. 40 in. DA 25 in. D 45 in 35 in. 60°

A: Draw the free-body diagram for the system.

Q: shown in fig. has the plane The 300 Ib block impanding motion Caused by Hhe horiZontal foree of 7.0…

A: Given data Force = 700 lb Weight of block = 300 lb

Q: The vertical mast supports the 4-kN force and is constrained by two fixed cables BC and BD and by a…

A: The free-body diagram of the vertical mast is given as, The vector BD is written as, The unit…

Q: Two farmers are pushing on a gate with forces FA and Fg, applied at locations A and Brespectively.…

A:

Q: The assembly shown has the dinensions given above. When a force of F 220 ib is applied, find the…

A:

Q: Need help. Please solve this and clearly state how you got your numbers and what formulas you used…

A: The free-body diagram along with the six unknown forces are given below.Now, Taking moment at centre…

Q: Need help. Please solve this and clearly state how you got your numbers and what formulas you used…

A: The free-body diagram along with the six unknown forces are given below.Now, Taking moment at centre…

Q: A force of 1000 lb is applied to the 600-lb horizontal beam supported by a hinge at A and a roller…

A:

Q: e 250 lb uniform crate (center of gravity at G) shown in e figure must be moved without tipping. The…

A: Given Data Force = 250lb Required  a) coefficient of static friction b) Push force

Q: 1.A uniform bar AB weighing 5OOKN, is fastened bya frictionless pin to a block weighing 100KN as…

A: Given DataWA=100kNWbar=500kNμkwall=0.268μkblock=0.2θ=45°To findP=? Free Body Diagram ***As per our…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.