Two forces are applied to tube AB as shown in the figure. Knowing that the tube has an outside diameter of 42mm and an inside diameter of 35mm, determine the stresses (normal and shear) at points "a" and "b".

Q: Neglecting the weight of the bracket, calculate the three principal stresses, and absolute maximum…

A:

Q: Part A The steel pipe in (Figure 1) has an inner diameter of 2.87 in. and an outer diameter of 3.12…

A: To find:The principal stress pointAGiven:the outer diameter of that the pipe is..The inner diameter…

Q: 2000 1 45001 3100 N

A: given; force in x-direction(Fx)=-2000N (compressive)force in y-direction(Fy)=-4500N…

Q: Determine the principal stresses and the absolute maximum shear stress. 2.5 ksi 4 ksi 5 ksi

A:

Q: Determine the principal stresses and the maximum shear stress correspondin the plane stress state…

A:

Q: A pipe assembly is subjected to a load of 200 N as shown. Determine the principle stresses,…

A:

Q: At a point on the free surface of a stressed body, the normal stresses are 20 ksi (T) on a vertical…

A:

Q: determine the developed stresses, the changes in length, and the changes in diameter for QI: The bar…

A:

Q: с 1 ft 2 ft B 150 lb-ft/ft A 2 ft A copper pipe is tightly secured to the wall at C and a uniformly…

A:

Q: Determine the normal and shear stresses at point B. 5-10 min 180 mm 180 mm 60 mm - 30 KN

A: Given data dimension of cross section = 180mm× 60 mm find the normal and shear stress at point B.

Q: The forces ar applied to the bar shown. Determine the normal and shearing stresses at (a) point a,…

A:

Q: Determine all the possible values of o> 0) and t(t> 0) in the figure knowing 1 the maximum shear…

A:

Q: Determine (a) the principal stresses and (b) the maximum in-plane shear stress and average normal…

A:

Q: A steel pipe 120 mm external diameter and 60 mm internal diameter is subjected to an internal…

A:

Q: Determine the equivalent state of stress on an element at the same point oriented 60° clockwise with…

A: As per our guidelines we are supposed to solve only one question if multiple questions are asked .…

Q: A closed cylindrical tank containing a pressurized fluid has an inside diameter of 320 mm and a wall…

A:

Q: Determine (a) the principal stresses and (b) the maximum in-plane shear stress and average normal…

A: Step 1: Step 2: Step 3: Step 4: solution is given above

Q: A force Q of magnitude 3kips is applied on the machine element AB of uniform thickness 0.8.…

A: Given, Q=3 kips The thickness, t=0.8 in

Q: N THE SYSTEM SHOWN AS BELOW, A FORCE OF 200 N AFFECTS ON THE PIPE SWITCH. CONSISTING AT POINTS A AND…

A:

Q: 30 mm and 40 mm, respectively. Determine the principal stresses and

A:

Q: PROBLEM 2. The forces shown in the figure are applied to a plate connected to a pipe with an outer…

A:

Q: A solid 30-mm-diameter shaft is used in an aircraft engine to transmit 86 kW at 1,250 rpm to a…

A: The diameter of shaft is The power transmitted is .The speed is The thrust developed is

Q: Determine (a) the principal stresses and (b) the maximum in-plane shear stress and average normal…

A: Given data: The normal stress in x-direction is: σx = -15 ksi (compressive stress is taken as…

Q: Determine the equivalent state of stresses in an element at the point representing (a) the principal…

A:

Q: Consider the stress element below. (a) Determine the three principle stresses and three shear…

A:

Q: 800 N D 120 N.m d = 8 cm 600 N Q / If the cross section of the femur can be approximated as a…

A: 1. Stress due to eccentric load of 800N P2 and 800N will create a momentMoment due to this…

Q: Given the plane element shown which is an element acted upon by combined stresses. a. Use Mohr's…

A:

Q: a force q of magnitude 3kips is applied to machine element ab. the uniform thickness of the element…

A: Given data Force (Q) = 3 Kips Thickness (t) = 0.8 in

Q: Q1/ For the state of plane stress shown below, construct a Mohr's circle and determine (a) the…

A:

Q: = A machine component is fabricated from a bent tube as shown below. One part of the tube lies along…

A: Outside diameter, d0=122 mmInside diameter, di=108 mmForce F=8.5 kNLengths,L1=258 mmL2=118 mmL3=281…

Q: In a cylindrical container, Gas is compressed to a pressure of 3 MPa. If the cylinder has a diameter…

A: Boiler shells, pressure tanks, pipes, and other low-pressure processing equipment all use…

Q: (7) For the state of plane stress shown in the figure, determine the normal and shear stresses…

A: Given data: The stress in the x-direction is σx=-50 MPa The stress in the y-direction is σy=0 MPa…

Q: The stresses shown on the right below act at a point on the surface of a cantilever beam, as shown…

A: Principal stress is defined as the maximum or minimum value of normal stresses and they act on that…

Q: A 28mm diameter round steel bar is 0.4m long. It is placed concentrically within a brass tube which…

A:

Q: A thin walled cylindrical pressure vessel with an inner diameter di = 600 mm and a wall thickness of…

A: The inner diameter is di=600 mm=0.6 m The wall thickness is t=17 mm The internal pressure is P=0.84…

Q: Determine the principal planes and the principal stresses for the state of plane stress resulting…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.