A thin walled cylindrical pressure vessel with an inner diameter di = 600 mm and a wall thickness of 0.84 MPa. It is also subjected to torque t= 17 mm is subjected to an internal pressure of p . T = 46 kN m and axial force F= 240 kN, which act through heavy plates attached to the ends of the cylinder as shown. Determine the principal stresses and the absolute maximum shear stresses at point A located on the outer surface of the cylinder. Opl = p2= T number (rtol=0.01, atol=1e-05) number (rtol=0.01, atol=1e-05) mber (rtol-001 atol=1e-05) A MPa MPa ? MPa

A thin walled cylindrical pressure vessel with an inner diameter di = 600 mm and a wall thickness of 0.84 MPa. It is also subjected to torque t= 17 mm is subjected to an internal pressure of p . T = 46 kN m and axial force F= 240 kN, which act through heavy plates attached to the ends of the cylinder as shown. Determine the principal stresses and the absolute maximum shear stresses at point A located on the outer surface of the cylinder. Opl = p2= T number (rtol=0.01, atol=1e-05) number (rtol=0.01, atol=1e-05) mber (rtol-001 atol=1e-05) A MPa MPa ? MPa

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider a point in a structural member that is subjected to plane stress. Normal and shear stress magnitudes acting on horizontal and vertical planes at the point are Sy= 41 MPa, Sy = 11 MPa, and S=-44 MPa. (a) Determine the principal stresses (o,l > 02) and the magnitude of the maximum in-plane shear stress Tmax acting at the point... (b) Find the smallest rotation angle 0, (counterclockwise is positive, cločkwise is negative) that will rotate to principal directions. Then show these stresses in an appropriate sketch (e.g., see Figure 12.15 or Figure 12.16) Answers: OpI = MPa. Op2 = MPa. Tmax | MPa.
An element in biaxial stress is subjected tostresses σx = -29 MPa and σy = 57 MPa, as shownin the figure. Using Mohr’s circle, determine thefollowing.(a) The stresses acting on an element oriented at aslope of 1 on 2.5 (see figure).(b) The maximum shear stresses and associated normalstresses.Show all results on sketches of properly orientedelements.
The stresses shown below act on horizontal and vertical planes through a point on the surface of a stressed body. Determine and show on a sketch the principal stresses and the maximum shear stress at this point. 50 MPa -30 MPa 35 MPa
A pressure-vessel head is fabricated by gluing the circular plate to the end of the vessel as shown in the figure.If the vessel sustains an internal pressure of 450 kPa, determine the average shear stress in theglue and the state of stress (axial and hoop components of stress) in the wall of the vessel.
The stresses shown act at a point in a stressed body. The stress magnitudes are Sx = 50 MPa and Sy = 250 MPa, acting in the directions indicated in the figure. Using the equilibrium equation approach, determine the normal and shear stresses at this point on the inclined plane shown. Assume β = 46°.
The figure shows the stresses at a point. Determine the principal stresses and the maximum shear stress. Show these values on the faces of properly oriented stress blocks.
PLEASE ANSWER ASAP THANK YOU
Gas stored in a cylindrical tank of inner radius 8mm wall thickness 50 mm. Gauge pressure 4 MPa. Determine the maximum shear stress in the wall?