Two forces are applied to an AISI 1050 HR post BD, as indicated. Knowing that the cross section of the vertical part of the post is 1.5 X 2.4 in., 1- Find the state of stress for the most critical point on the round shaft (i.e., point H) 2- build the mohr's circle at point H. 3- Apply the failure theories to find the factor of safety. 4-Calculate the total strain energy in the post BD. 5-Find the deflection of point C using Castigliano's theorem in the direction of force 500 Ib. 6-Find the factor of safety of the post BD using the langer-static criterion, 7-Draw the the langer static criterion and locate the load line. 6000 lb Z 4 in. 1 in. 1.5 in. 3.25 in. y D B 2.4 in. 1.75 in. 500 lb 6 in.

Two forces are applied to an AISI 1050 HR post BD, as indicated. Knowing that the cross section of the vertical part of the post is 1.5 X 2.4 in., 1- Find the state of stress for the most critical point on the round shaft (i.e., point H) 2- build the mohr's circle at point H. 3- Apply the failure theories to find the factor of safety. 4-Calculate the total strain energy in the post BD. 5-Find the deflection of point C using Castigliano's theorem in the direction of force 500 Ib. 6-Find the factor of safety of the post BD using the langer-static criterion, 7-Draw the the langer static criterion and locate the load line. 6000 lb Z 4 in. 1 in. 1.5 in. 3.25 in. y D B 2.4 in. 1.75 in. 500 lb 6 in.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please don't provide handwritten solution ......
Please find the solution from the book or solve it like if it was a book solution. Do Not ShortCut the Static, V(x), and M(x) Analyses
Find the initial length of rod if strain value is 0.0003 and change in length value 0.3 mm
Copied or wrong solution get multiple downvote for sure. 1)A cylinder with a 0.3 m inner diameter and 0.4 m outer diameter is internally pressurized to 140 MPa. Determine the maximum shear stress at the outer surface of the cylinder.
Please show all steps
echanics of Materials I X t.php Two loads P act as shown, one parallel to (x0) and another parallel to z0; each load P equals 1.5 kN. The crankshaft dimensions are b1 = 55 mm, b2 = 150 mm, and b3 = 45 mm. The diameter of the upper shaft is d= 22 mm. Determine the normal stress at point A, which is located on the surface of the upper shaft at the z0 axis. Yo Letferbimtse ENene 302 704 MPal
Provide Exact Answer ,Attempt If you are 100% sure.
The principal stresses shown below are calculated at two different cross sections of a brittle machine part. Determine if the cross section A or B is safer (Sy = 50 MPa, Sut = 100 MPa, and Suc = 200 MPa). 0,50 MPa + 0₂ = -20 MPa A 0₂=-20 MPa 0₁ = 50 MPa a, 20 MPa - ₂ =-120 MPa B 0-120 MPa a₁ = 20 MPa
The cylinder head of the gas engine has a dimension of a 254 mm x 450 mm. There are ten (10) bolts on the block. The explosion pressure is 14 kg/cm² and the studs are made of ordinary bolt material, with Sy = 606,760 kPa Find the stress area in in².
Q1 A round bar is subjected to a rotating force. State what type of stress is induced in the bar and why?
The maximum ( Tresca's Theory) normal stress theory FS of the following Tresca's, Rankines failure the Determine lelement stress show = 200 MPa, and using the învolved envelope sy V-0.3 100 MPa 80 MP
Please full answer with drawings and BIG clear Handwriting. Please