Two equal angles ISA, 100 mm x 100 mm of thickness 10 mm are placed back-to-back and connected to the either side of a gusset plate through a single row of 16 mm diameter rivets in double shear. The effective area of the connected and unconnected legs of each of these angles are 775 mm2 and 950 mm?, respectively. If these angles are not tack riveted, the net effective area of this pair of angles is

Two equal angles ISA, 100 mm x 100 mm of thickness 10 mm are placed back-to-back and connected to the either side of a gusset plate through a single row of 16 mm diameter rivets in double shear. The effective area of the connected and unconnected legs of each of these angles are 775 mm2 and 950 mm?, respectively. If these angles are not tack riveted, the net effective area of this pair of angles is

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

8) what is the flexural rupture capacity of the shear plate of the shear connection in kips? (2 decimal places) A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksi
Define Vane Shear Test (VST)
A flanged bolt coupling consists of 9-17-mm-diameter steel bolts on a bolt circle 400 mm in diameter, and 5-17-mm- diameter steel bolts on a concentric bolt circle 300 mm in diameter. What torque can be applied without exceeding a shearing stress of 63 MPa in the bolts? Answer must be in kN-m.
Determine the rivet value of 20 mm diameter rivets connecting 10 mm plate and is in (a) single shear and (b) double shear. The permissible stresses for rivets in shear and bending are 80 MPa and 250 MPa respectively and for plate in bearing is 250 MPa. (iy The one-way slab of a reading room is estimated to have a thickness of 100 mm along with thickness of finishing as 75 mm. The slab is to carry a live load of 4 kN/m2. Determine the factored loads (a) for strength, and (b) for serviceability (ii) limit states. Take Unit weight of concrete as 25 kN/m³ and finishing as 22 kN/m³.
The figure along with the question is this, can you double check if the answer will still be the same?
The effective throat thickness of a fillet weld not to be greater than a. 0.3t b. 0.6t C. t d. 0.5t
.
1. Given the figure below. The rivets are 25 mm in diameter. Calculate the maximum safe load P that can be applied in the connection if the Shearing stress in the rivets is limited to 97 MPa and the bearing stress in the plates is limited to 125 MPa. a. 190.46 KN b. 162.75 KN C. 250 KN D. 225 KN P egnibsol arif to tiuzes es menpsib iseria ali aworie rhand behoque vigme A m.VIX ni inomom naqe mum20mm Sheerle navig ont of flueen lw BA nete O 120mm p 100m .0 is bsol bateineando arif eitadW.2 100
00 AT&T LTE 10:14 AM e* 49% D+ a bbl-app.learn.fresnostate.edu 1 of 2 Determine the average shear stress in the 20-mm diameter pin at A. |30 kN 5 3 \B 2 m - 4 m
Problem 17. The welded connection shown in the figure uses electrodes E70XX. The nominal weld strength of the connection is: a 184.40 kN b 245.87 kN c 430.27 kN d 485.59 kN 18. For the connection shown in problem 17, the LRFD design strength is: a 322.70 kN b 364.19 kN c 387.24 kN d 437.03 kN 19. For the connection shown in problem 17, the ASD al strength is: a 215.14 kN b 242.80 kN c 322.70 kN d 387.24 kN
draw the FBD of joint B
please draw complete and neatly