1. Given the figure below. The rivets are 25 mm in diameter. Calculate the maximum safe load P that can be applied in the connection if the Shearing stress in the rivets is limited to 97 MPa and the bearing stress in the plates is limited to 125 MPa. a. 190.46 KN b. 162.75 KN C. 250 KN D. 225 KN P O egnibsol arif to tuzes as mengeib seria ali aworie rhand behoque vigme A m.Xml Inomom naqe mumzo 000 Sheerle nevig ont of flugen lliw BA ne p 100pm 120mm

1. Given the figure below. The rivets are 25 mm in diameter. Calculate the maximum safe load P that can be applied in the connection if the Shearing stress in the rivets is limited to 97 MPa and the bearing stress in the plates is limited to 125 MPa. a. 190.46 KN b. 162.75 KN C. 250 KN D. 225 KN P O egnibsol arif to tuzes as mengeib seria ali aworie rhand behoque vigme A m.Xml Inomom naqe mumzo 000 Sheerle nevig ont of flugen lliw BA ne p 100pm 120mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

"1-80. Determine the maximum allowable torque T that can be transmitted by the joint. The shear pin A has a diameter of 25 mm, and it is made from a material having a failure shear stress of Tai 150 MPa. Apply a factor of safety of 3 against failure. 100 mm
CH2-Hetant pa-Aote Acrobet Pro titended Ee Vien Decumem Comments Forme Tacs adanced wedew Hep 2/86 If the resultant of the loads shown passes through point B, determine the equivalent force-couple system at O. 45 kN 54 kN 1.2 m 0.9 m 0.9 m M 18 kN ahid ham
i need the answer quickly
None
b) Three lona wires, Ctwo bronze and one steel) are equal in lanate and fuppert afe 6715KN at and support mneete rigiel bar o7 iskN ef Comnectedt their bottoms: IF the cross seetion ealeulate a' esch wire is120mm2, of area the stresses in each wire and also the strains in each wire Take F=loukH/mm", Esz200KHlmm²
Topic: Bearing stress
The se extra examples ara presented by Mohammed Dheyaa 2021@ 4.W.l Given V, = 25m/s S.g.= 0.83 Find the force raquired F=3. plate d=somm yet
H.W find longitualinal and hao tensile stresses in the wall of vessel Shown in figure, if the internal Pessure is 0.9 41a and thickness ef wall is 6.4mm? Ans: 7 =42.19 M H= 62.8 MG AIS finl مرّر للأعلى لاستعراض الفلاتر إضافة شرح. . . + mum < V
The homogeneous bar AB weighing 1800 lb is supported at either end by a steel cable. Calculate the smallest safe area of each cable if the working stress is 18 000 psi for steel. 2ft 1.5 ft a. 0.075 in? c. 0.100 in? d. 0.050 in? 5ft b. 0.128 in? Ans:
HW A Solid Steel bar of dlameter 6omm andlengtj2. 350mmis p laced inside analuminum cylinderof Insie diameter Fommm and out side dlameter lomm, a compressive load of loo0 law is applled on the assembi n find the stresses in the barand the cylinder? take e Est= 200GPA and EAl= FoGla- SAL? D=u.25 %D লি Cover Plate 0.25mm di 350mm A lum. cylinder Steel bar
Draw shear and merrent dingrams for pach member of he frame. Assume Ohe point A au pin Support and point B as al voller suppork. 多 4047 20 OB te
please use only set 1 data table thank you this is non graded