Two designs for a shaft are being considered. Both have an outside diameter of 50 mm and are 600 mm long. One is solid but the other is hollow with an inside diameter of 40 mm. Both are made from steel. Compare the torsional shear stress, the angle of twist, and the mass of the two designs if they are subjected to a torque of 850 N · m.

Q: A circular shaft with 50mm and its lenght is 850mm long and is made of steel, the shaft is subjected…

A: GIVEN :- diameter : d=50mm length: L=850 mm Torque subjected: T=800Nm (to determine θ we need the…

Q: A standard 25-HP electric motor operates at 1800-RPM. If the motor is connected to a pump in the…

A: The power available, P = 25 hp The speed of motor, N = 1800 rpm The diameter, d2 = 1.25 in The…

Q: Calculate the angle of twist at point A. A for the following diagrammed problem. There is a 1600…

A: The diameter of shaft AB is .The diameter of shaft CD is .The diameter of gear B is .The diameter of…

Q: Determine the minimal value of a radius of the circular-solid shaft in problem 1 such that the…

A:

Q: an aluminum shaft is 6ft. and has toruq of 500 lb-ft. the shear stress is 6500 psi and the angle of…

A:

Q: A standard 25-HP electric motor operates at 1800-RPM. If the motor is connected to a pump in the…

A: The power available, P = 25 hp The speed of motor, N = 1800 rpm The diameter, d2 = 1.25 in The…

Q: what is the Moment at point A

A: First find the moment produce by given torque as follows.

Q: A solid circular shaft is subjected to a torque of 21,334 in-lb.  Calculate the diameter required if…

A:

Q: 2. The diameters of the solid shafts are: AB is 0.6 in, BC is 0.75 in. and CD is 0.9 in. The applied…

A:

Q: Both shafts have the same diameter-2cm and are made of low quality steel G-77 GPa. A torque of 1200…

A:

Q: 3. A steel shaft 60 in. long has applied to it a 10,000 in-lb torque by a pulley located at the…

A:

Q: Problem 5-13: The shaft has an outer diameter of 100 mm and an inner diameter of 80 mm. If it is…

A:

Q: A hollow shaft with a length of 1103mm and outer diameter 73mm and inner diameter 50mm is required…

A:

Q: 3. Knowing the rotation speed: n=300r/min and the power of applying on each wheel: P₁-200kW. P-50kW,…

A: Given Data: n=300 rpmP1=200 kWP2=50 kWP3=50 kWP4=100 kWτall=120 MPaLAB=LBC=LCD=1.5 mR=20 mm   To…

Q: The figure shows a shaft carrying three gears that rotates at 1150 rpm. Gear A delivers power =10kw…

A: Given, Gear A deliver 10KN Gear C deliver 15KN A shaft carrying 3 gears that rotates at 1150 rpm…

Q: The figure shows a shaft carrying three gears that rotates at 1150 rpm. Gear A delivers power to a…

A:

Q: Oh no! The bearing at the wall on the left has been damaged. It is now acting like another gear that…

A:

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.