Two columns are 4,506 mm away from each other measured center tocenter. The loads supported by the columns are listed below. Effective soilpressure is 103 kPa.Left Column (421 mm X 725 mm) (Note that the 725 mm side is flushedto the property line of the building and is parallel to the short side of thefootingDL=720 KNLL-859 KNRight Column (594 mm X 729 mm) (594 mm side is parallel to the longside of the footing)DL=860 KNLL-856 KNCalculate the nominal wide beam shear stress in MPa at the left column.Use an effective depth of 700mmDo not round off intermediate values. Use exact values for L, B,and other variables.Answer in 4 decimal places

Two columns are 4,506 mm away from each other measured center to center. The loads supported by the columns are listed below. Effective soil pressure is 103 kPa. Left Column (421 mm X 725 mm) (Note that the 725 mm side is flushed to the property line of the building and is parallel to the short side of the footing DL=720 KN

Two columns are 4,506 mm away from each other measured center to center. The loads supported by the columns are listed below. Effective soil pressure is 103 kPa. Left Column (421 mm X 725 mm) (Note that the 725 mm side is flushed to the property line of the building and is parallel to the short side of the footing DL=720 KN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rectangular footing is to be used to support a 300 x 400 (400mm side is parallel to the long dimension of the footing) column loaded with 420 kN dead load and 540 kN live load. One side of the footing is 4.0m. Use effective soil pressure of 70 kPa. F'c = 35 MPa and fy = 420 MPa. Use minimum steel ratio for longitudinal bars as 0.0018. Calculate the required number of 16mm bars along the short direction inside the band width.Calculate the total required number of 16mm bars along the short direction outside the band width. Use the governing thickness based on shear requirements on both
Q1. Determine the vertical displacement of end C of the precast concrete column. Econcrete = 4.2 (10³) ksi.
Design a square footing for a 18-in. square column and a superimposed dead load of 200 kips and a live load of 300 kips. The maximum permissible soil pressure is 4000 psf. Use concrete with a design strength of 3 ksi and grade 40 reinforcing bars with yield strength of 40 ksi.
Assume a 27-in.-thick square footing (d 23 in) supports an 18-in.-square tied interior column. Assuming that the shear force V = 827 kips and the concrete used is 3000-psi normal-weight concrete, what exactly is the required depth to resist the two- way shear? Select one: a. 30.7 in b. 16.2 in А C. 36.8 in d. 23.9 in
?CE
Design a one-way slab having a simple span of 3m. The slab is to carry a uniform live load of 7,500 Pa. Assume f°c = 27.6 MPa and fy= 276 MPa for main and temperature bars. Use 23.5kN/m3, 12 mm for main bars and 10 mm for temp bars.
Problem 4 A footing supports a 200mm thick concrete wall. Wall loads: = 175 Dead Load kN/m = 89 Live Load kN/m = 20.6 Concrete, f'c MPa = 415 Steel, fy MPa Unit weight = 23.6 of concrete kN/m3 Factored = 1.2D load + 1.6L combination Thickness of = footing 350mm Steel Cover ( bottom of footing to centroid of 90mm bars)
Calculate the Load distribution of slabs to beams 3, 4 and C using 10kPa load multiplied by the tributary width. Colored box represents columns and uncolored represents beams.
The floor shown below with an overall depth of 125 mm is to be designed to carry an imposed load (LL) of 2.5 kN/m² plus floor finishes and ceiling loads (DL) of 1.5 kN/m². Calculate the factored loads acting on beams CD. Assume unit weight of concrete is 24 kN/m². E 2. F 3.0 m 5.0 m Depth 125mn 0.125m -hh=2.5 kN/m² - PL = 1.5 kNm² - u. W of compete 24 KN/m³ A 80m B
A column 24 in. square, with f'c = 4ksi reinforced with 10 No. 10 bars, As=12.7 square inches. fy=50 ksi, supports a dead load of 276.06 kips and a live load of 175 kips. The soil (fill) has a unit weight of 100 pcf and the concrete unit weight is 150 pcf.The allowable soil pressure q(a)is 2500 lb/ft^2. Design a square footing with base 6 ft below grade, using f'c= 4 ksi and fy= 50ksi
Need Complete an elaborate solution Design a square base plate to support 12 mm thick pipe column with an inside diameter of 400 mm. The base plate minimum dimension is 500 mm. To design plate thickness, convert the circular perimeter of the pipe into an equivalent square with an area equal to the original circle. The loads are PDL = 700 kN and PLL =320 kN. Assume that the pipe is to rest on a very wide slab. Use A-36 steel and concrete fc’ = 25MPa and ASD.