Answered: 12) Determine the shear capacity, øVe,…

12) Determine the shear capacity, øVe, for a one foot- wide design strip for a solid one-way slab 8 in. deep of normal weight concrete. fe=3 ksi, f,= 40 ksi, d=6.94 in. %3D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars…

Q: under the following boundary conditions (x = 0, y = 0); (x = L, y = yMax). what kind of beam is…

A: Beams can also be described with their boundary conditions. In the given question, When x=0…

Q: 3. Determine the size of the base plate using Fy = 36 ksi. The column size is W14 x 82 and the load…

A: The yield strength of the plate (fy) = 36 ksi The column section used = W14×82 The magnitude of the…

Q: Question 19 A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with…

A: Given:- b=230mm d=500mm 4-20mm diameter bars top of 2-16mm bars concrete cover to bar centroid at…

Q: the final answer should be fc= 10.07 MPa and fs = 155.9 MPa

A: In this problem we calculate flexural stress in concrete and steel using equalent area method. In…

Q: 4. A T-beam has the following properties: bf 820 mm, bw = 250 mm, d= 470 mm, t 100 mm. Concrete…

A: To improve its tensile strength, reinforcement ( steel reinforcing rods ) is embedded in it. As per…

Q: A rectangular concrete beam has a width of 300mm and an effective depth of 450 mm to centroid of the…

A: Given: b = 300 mm d = 450 mm Ast=6×π4×322=4825.5 mm2Asc=2×π4×282=1231.5 mm2 fc = 34.5 MPa fy =345…

Q: 3. A column shown below has tie reinforcement conforming to ACI 25.7.3. Assume normal- weight…

A: Given: concrte stress fc'=6000 psi allowed stress in concrete fc=60002=3000 psiand for steel grade…

Q: a rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars…

Q: A rectangular concrete beam has a width of 300mm and an effective depth of 450 mm to centroid of the…

A: Given data - Width =300mm Effective depth = 450mm Reinforcement = 6 - 31mm bars ( tension) and 2 -…

Q: • A rectangular beam has the dimensions b=250mm, h=650mm, and d=600mm and is reinforced with three…

Q: 2. Design a two-way slab having a dimension of 3m x 4m. The slab is to carry a uniform live load of…

A: Step 1:Step 2:Step 3: Step 4:

Concept explainers

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.

Question

12) Determine the shear capacity, øVe, for a one foot- wide design strip for a solid one-way slab
8 in. deep of normal weight concrete. f. 3 ksi, f, 40 ksi, d=6.94 in.
%3D

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 : Data

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Problem 4.39 Design the one-way slab shown in the accompanying figure to support a live load of 10 kN/m2. Do not use the ACI thickness limitation for deflections. Assume concrete weighs 23.5 kN/m.f 28 MPa and f, = 420 MPa. Use p = Pmur: (One ans. 240-mm slab with #25 @ 140-mm main steel) -10m Width of the slab is 10m WL = 10kN/m2 And draw slab section showing all reinforcements along with the slab
A rectangular reinforced concrete beam has a width of 300 mm andan effective depth of 450 mm to centroid of the tension bars. Thebeam is reinforced with six 32 mm ɸ tension bars placed in twolayers with the outer layer having a depth of 478 mm, and two 28mm ɸ compression bars with centroid 65 mm from the extreme concretefiber. Use the 2010 NSCP, fc’= 34.5 MPa and fy = 345 MPa. Assumethat the concrete displaced by the compression steel shall not beneglected and that the compression steel yields. Det. the following:19. The balanced steel ratio if the beam is singly reinforced. a. 0.04607 b. 0.03555c. 0.02721 d. 0.03672 20. The maximum steel ratio for a singly-reinforced section intension control. a. 0.03555 b. 0.04607c. 0.03672 d. 0.02721 21. The maximum steel ratio for a doubly-reinforced section intension control. a. 0.02721 b. 0.03672c. 0.03555 d. 0.04607
Problem 1-3: All stirrup information is provided, including spacing. You will find the resultant shear capacity. fy of stirrups is 60 ksi and f'c = 3,500psi. For each problem: a) Compute Vc from the concrete properties, and calculate the Vs provided by the stirrup information (Vs = Avfyd/s). b) Compute the design shear capacity Vn = o(Vc + Vs). c) Check to see if the given spacing s is acceptable based on ACI limits of Smax. d) Check to see if the section is usable (V ≤ 8√fcbwd ?)
A rectangular beam has the dimensions b=12in., h=26in., and d=24 in. and is reinforced with three No. 11 bars so that As-4.68 in.². The normal-weight concrete compressive strength is 5000 psi. and the tensile strength (modulus of rupture) can be calculated as per ACI318-14. The Grade of the steel is 60. Determine the nominal moment strength M, and the moment capacity Mn. b=12 in. Figure 1. d=24 in. h=26 in.-
A prestressed rectangular beam 0.50m x 0.75m has a simple span of 10m and is loaded with a uniform load of 45 kN/m including its own weight. The prestressing tendon is 0.225 m from the bottom and produces an effective prestress of 1600 kN. Compute the fiber stress distribution in the concrete at midspan (bottom fiber) due to axial and transverse loading. Select one: a. 3.26 MPa b. 1.96 MPa c. 2.61 MPa d. 4.08 MPa A prestressed rectangular beam 0.50m x 0.75m has a simple span of 10m and is loaded with a uniform load of 45 kN/m including its own weight. The prestressing tendon is 0.225 m from the bottom and produces an effective prestress of 1600 kN. Compute the fiber stress distribution in the concrete at midspan due to transverse load. Select one: a. 15 MPa b. 9 MPa c. 12 MPa d. 7 MPa
Question 33 A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 350 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars. Determine the maximum steel ratio if the beam is singly reinforced in negative bending with the given material strengths and the tensile strain is limited to 0.004 upon crushing of concrete. Write the answer in 5 decimal places only.
The cross section of a reinforced concrete beam is shown below .( 5 - No . 10 bars )are designed as the bottom bars and No. 3 stirrups as the vertical reinforcement . Considering a clear cover thickness = 1.5 in , sketch the layout of reinforcement and show bar spacings per AC1318-19 . Assume maximum aggregate size = 1 in and the minimum required effective depth of bottom bars = 20 inches .
Show solution please
A pretensioned prestressed beam has a rectangular cross section of 6 in. width and 20 in. total depth. It is built using normal-density concrete with a specified strength f = 4000 psi and a strength at transfer of f' = 3000 psi. Stress limits are as follows: fi = 164 psi, f. = -1800 psi, f. = 474 psi, and fes = -1800 psi. The effectiveness ratio R may be assumed equal to 0.80. For these conditions, find the initial prestress force P, and eccentricity e to maximize the superimposed load moment My + M, that can be carried without exceeding the stress limits. What uniformly distributed load can be carried on a 30 ft simple span? What tendon profile would you recommend?
Design a simply supported one-way reinforced concrete floor slab to span 10 ft and carry a service live load of 175 psf and a service dead load of 25 psf. Use fc' = 3000 psi and fy = 60,000 psi. Make the slab thickness to 12-in. increments. a. Design the slab for the ACI Code minimum thickness. b. Design the thinnest possible slab allowed by the ACI Code.
PLEASE SOLVE AND BOX ALL FINAL A LITTLE CONFUSED