Compute soil pressure, factor of safety for sliding and overtuming for the retaining wallshown. Calculate reinforcing steel for the stem only. Weight of concrete=150 pcf, weightof earth=110 pcf, coefficient of friction=D0.45, equivalent fluid pressure=33 pcf. fc=4000psi, fy=60,000 psi,5' - 0'10' - 0"10-191

Answered: Image /qna-images/answer/6dbd27bf-5b41-448f-bc5b-b6b3228ca0ef.jpg

Answered: e soil pressure, factor of safety for s…

Engineering

Civil Engineering

e soil pressure, factor of safety for s Calculate reinforcing steel for the st 110 pcf, coefficient of friction=0.45

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

In a steel flat plate a state of plane stress available. Calculate o, and principal stresses if 0₁-140 N/mm², p=0.25, 1₁,-40 N/mm², e,- -3.6 × 10 and E-2× 10³ N/mm².
A scuba tank is being designed for an internal pressure of 2,650 psi with a factor of safety of 2.0 with respect to yielding. The yield stress of the steel is 69,000 psi in tension and 20,000 psi in shear. (Assume that the given radius or diameter is an inside dimension and that all internal pressures are gage pressures.) (a) If the diameter of the tank is 7.0 in., what is the minimum required wall thickness (in inches)? inches (b) If the wall thickness is 0.25 in., what is the maximum acceptable internal pressure (in psi)? psi
Number 1 (parts i, ii, iii) please :)
1. The details of the cantilever beam are shown below. Use f'c = 28 MPa, fy = 415 MPa, and fyt = 275 MPa. Notes:• All dimensions are in millimeters.• Column reinforcement not shown for clarity• Column and beam are neither exposed to weather nor contact with the ground.• Analyze as singly reinforce beam only.• Neglect the weight of the beam.• Concrete isnormal weight and reinforcements are galvanized. d. What is the flexural capacity of the beam at face of support in kNm? e. What is theshear capacity of the beam at face of support in kN? f. What is the maximum Pu (kN) that can be applied at the free end of the beam consideringflexure and shear? g. What is the requiredminimum cut length (mm) of each stirrup? Roundyour answer to nearest safe25 mm.
Question #5. Calculate the allowable axial compressive load for a stainless-steel pipe column having an unbraced length of 20 feet. The ends are pin-connected. Use A-11.9 inch, r-3.67 inch and Fy- 40 ksi. Use the appropriate Modulus of Elasticity (E) per material used. All the calculations are needed in submittal. O 212 kip O 202 kip O 196 kip 224 Wip
Give me right solution
Dont round off initial values, round off final ans only ty
A 1.65m long rod with a circular cross-section is subjected to a tensile load of 50 kN. The rod is made from AISI 1040 hot-rolled steel. The allowable tensile stress is 165 MPa. The rod is permitted to elongate up to 7mm without causing any issues. The proportional limit for the steel is 180 MPa. (A) Compute the required area necessary to meet the stated requirements based on allowable stress. Express your answer in square millimeter units as an integer. (B) Compute the required area necessary to meet the stated requirements based on allowable elongation. Express your answer in square millimeter units as an integer.
Hope your help concrete design (CE410) thanks
Typewritten for upvote. Thank you
(e) Regardless of the load duration (i.e., standard, permanent, or short term), the wet service condition causes almost the same reduction in the compressive strength for glulam sections. (
Determine the values of the distance cfrom the extreme concrete corppression fibers to the neutral axis, andr, for the beam shown in the following Figure fy 60,000 psi and fc 3000 psi. 0.003 21 in d-c 389 bars 3.00 in) = (0.003) 12 in Select one: a. 6.90 in, 0.0061 b. 6.25 in, 0.0069 c. 7.50 in, 0.0085 d.5.93 in, 0.0076