Two cables are tied together at C and are loaded as shown. Knowing that P 117 N and R = 442 N, Determine the tension in cables AC. A B 30°| 30° R C /45° C

Q: two cables AB and AC, are fastened together at A as shown in the below figure. Determine the tension…

A: ∝=tan-134=36.870°θ=tan-135=30.964°

Q: s. Determine the tension in each wire.

A:

Q: Determine the force in each member of the bridge truss shown. State whether each member is n tension…

A: Solution: Considering the diagram:

Q: A rigid bar AB, pinned at end A, is supported by a wire CD and loaded by a force P at end B as shown…

A: Given:  E =210 GPa  Displacement at B not more than 6mm Diameter of wire = 5mm   To Find: Maximum…

Q: 70 KN 4 m D 40 KN 4 m B

A: Solution Calculate the degree of static indeterminacy DSI=m+re-2jDSI=8+3-2*5DSI=1

Q: 6-53) A beam is constructed from four pieces of wood, glued together as shown. If the moment acting…

A: Moment = 450N.m y= 120 I= 2×15×240312+2200×20312+200×20×1102I=181.6267 mm4 σmax=MI×y=…

Q: Determine the force in each member of the loaded truss. The force is positive if in tension,…

A:

Q: a. The beam weighs 3600N. Draw the V and M diagram. b. Assume we do not know the weight of the beam…

A: 1-If Beam weighs 3600 N then drawing of SFD and BMD 2- if Beam Weighs is not know then finding of…

Q: Q4 - For the given beam and cross section, at point B on section A-A (mid-span), determine the…

A:

Q: 3.) Consider the 2D frame shown below. There are pins at A, C, D. Point E is halfway between A and…

A:

Q: If the load P on the beam causes the end C to be displaced by 10mm downward, determine the normal…

A: Solution; Given that; Deflection of 'C' ⇒δc=10 mm

Q: Q2. The beam supports a uniform dead load of 0.4 kft, a live load of 1.5 kft, and a single live…

A:

Q: The structure shown is made of many weightless, solid and rigid members pinned together at different…

A: cut through structure is:

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A: The below structure is given; Where, P = 440 N

Q: Aa B C -3 m- 6 kN D E -3 m- 6 kN F G -3 m- 6 kN -3 m- 0000 4 m

A:

Q: P5 The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting…

A:

Q: 6. The truss pinned to the floor at D, and Supported by a roller at roller at point A is loaded in…

A:

Q: A three-element truss has the configuration shown in Figure 5. A vertical load is applied to the…

A: P = 5KN A = 100mm2 E = 70GPa = 70 x 103 N/mm2

Q: Calculate the force in HE. Assume tension = positive. Given information repeated for your…

A:

Q: 1. A tower guy wire is anchored by means of a bolt at A. The tension in the wire is 4000 N.…

A:

Q: *5-20. The trusses are pin connected and suspended from the parabolic cable. Determine the maximum…

A: A truss is a structure made up of members arranged in connected triangles so that the entire…

Q: 2. Determine the horizontal and vertical components of force at pin B and the normal force the pin…

A:

Mechanics of Solids

It is the study of the behavior of solid materials, their characteristics under various circumstances such as variation in external forces, temperature, and other internal factors. It is one of most important study in the field of engineering science, especially chemistry and mechanical engineering. In rigid body, the idealization of the solid body in which deformation is neglected. Deformation is known as the force acting on the solid state system which exerts change in its shape of the body but it continues to be at rest or in a uniform motion but it cannot accelerate. But those solid systems do have elasticity, compressibility and can be bent. This field is very vast since there are wide range of materials around us.