Two bars are subjected to F=20 kNforce as shown in Figure and a0.5 mm0.4 m0.6 mtemperature rise of 100 °c.Determinea) Reaction forces at the walls AF=20 kNBand B.b) The change in length of thebronze barBronzeA = 1500 mm?E = 105 GPaa = 21.6 x 10-CAluminumA = 1800 mm2E = 73 GPaa = 23.2 x 10ºC%3D

Answered: Image /qna-images/answer/4051d279-7c08-419d-9447-4929e840e22d.jpg

Two bars are subjected to F=20 kN force as shown in Figure and a 0.5 mm 0.4 m 0.6 m temperature rise of 100 °C. Determine a) Reaction forces at the walls A and B. F=20 kN B b) The change in length of the bronze bar Bronze A = 1500 mm? E = 105 GPa a = 21.6 x 10-8ºC Aluminum A = 1800 mm? E = 73 GPa a = 23.2 x 10°C

Two bars are subjected to F=20 kN force as shown in Figure and a 0.5 mm 0.4 m 0.6 m temperature rise of 100 °C. Determine a) Reaction forces at the walls A and B. F=20 kN B b) The change in length of the bronze bar Bronze A = 1500 mm? E = 105 GPa a = 21.6 x 10-8ºC Aluminum A = 1800 mm? E = 73 GPa a = 23.2 x 10°C

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q3: A steel rod is rigidly attached between an aluminum rod and a bronze rod as shown. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in steel of 140 MPa, in aluminum of 90 MPa, or in bronze of 100 MPa. BRONZE = 500 mm² 4P STEEL A = 400 mm² 2.5 m 2.0 m ALUMINUM A = 200 mm² P 1.5 m 2 2P
The structure consists of two bars. Axial loads 40 kN and 10 kN are loaded as shown in Figure B. Determine: a) Global stiffness matrix b) Nodal displacement c) Stress in each bar Table 2 Steel Aluminium Brass Area 400 350 350 (mm³) E(Gpa) 200 70 83 Aluminum Brass Steel 40 kN - 10 kN L 500 mm 400 mm 300 mm
PLEASE ANSWER ASAP TY! The two bars (1) and (2) are made of the aluminum with E = 70 GPa, has the same cross section of 100 mm x 20 mm, and supported by rigid supports at A and C. The coefficient of thermal expansion of the material is 23 x 10–6/oC. At T = 25oC, the two bars have a gap of 5 mm as shown. a) What is the reaction force (in KN) at fixed support A when the temperature is 100oC? b) What is the reaction force (in KN) at fixed support C when the temperature is 100oC? c) What is the stress (in MPa) in bar (1) when the temperature is 100oC? d) What is the stress (in MPa) in bar (2) when the temperature is 100oC?
D 12KN B A 10KN 28kN + + 60KN 44kN + 120cm 80cm Ост 40cm Figure 1 a) Draw a Free Body Diagram for each section of the member above. b) Determine the force acting on the section BC. c) Draw a Normal Force Diagram for the figure above. d) Calculate the stress induced in the member BC if the diameter of the rod is 55.2791mm. e) Determine the total elongation of the rod.
An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure below. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in steel of 200 MPa, in aluminum of 115 MPa, or in bronze of 145 MPa. Aluminum A = 400 mm2 Bronze A = 200 mm2 Steel A = 500 mm² P 2P 4P 2.5 m 2.0 m 1.5 m
HW: 1-1-12 Find the axial stress in rods AB and BC. AB has a diameter of 25 mm and BC has a diameter of 15 mm. State if they are in tension (T) or compression (C). Answer(s): B A 6000N 8000N
a) Determine the tensile force T’ in the rope on the side connected to joint B: b) Determine the internal compressive normal force ƒBC in the tube BC: c) Determine the horizontal reaction force Rx and the vertical reaction force Ry in joint A: d) Determine the moment M of the center of bar AB: e) Determine the compressive stress σBC in the tube BC: f) Determine the critical load Pc for the tube BC: g) Which of the following statements about the tube BC is correct: A. The tube BC fails due to yielding B. The tube BC fails due to buckling C. The tube BC fails due to both yielding and buckling D. The tube BC is safe against both yielding and buckling h) Pin C has a diameter of 30 mm; calculate the shear stress τ of the pin C, when considering one cross-section for shear stress calculation:
Two round solid bars of different materials are connected in series against rigid supports as shown in Figure 4. Determine the stress in each bar and the support reactions if temperature is increased by 18° C. Bar A da, EA, A Bar B dв, Ев, ав LA LB Figure 4 Use the following information. Bar, B: Length, LB Diameter, dB Poisson's Ratio Young's Modulus EB = 210 kN/mm2 Coefficient of expansion aB = 12.4x106 °C- Bar, A: Length, LA Diameter, dA = 25mm =D40 mm = 10 mm 30 mm S. = 0.28 =D0.32 = 70 kN/mm² Coefficient of expansion aa = 16.5x10-6 °C-I Poisson's Ratio %3D Young's Modulus EA
Find the force P which is applied on point B of the triangle ABC, as * :shown in the figure below P=? B T= 600 N 5 m C/60 D -2.5m- P=216.7N P=226.7N P=206.7N
The AB part of the rod is steel and is 100mm in diameter.The BC part of the rod is copper and its diameter is 80 mm. a)Draw the normal force diagram of the rod. b)Calculate the normal stresses in sections AB and BC. c)Calculation of the total length change of the bar.