Two axial members are used to support a load P applied at joint B. Member (1) has a cross-sectional area of A = 3,080 mm2 and an allowable normal stress of 180 MPa. • Member (2) has a cross-sectional area of A2 = 4,650 mm2 and an allowable normal stress of 75 MPa. Determine the maximum load P that may be supported without exceeding either allowable normal stress.

Two axial members are used to support a load P applied at joint B. Member (1) has a cross-sectional area of A = 3,080 mm2 and an allowable normal stress of 180 MPa. • Member (2) has a cross-sectional area of A2 = 4,650 mm2 and an allowable normal stress of 75 MPa. Determine the maximum load P that may be supported without exceeding either allowable normal stress.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The rigid beam BC is supported by rods (1) and (2). The cross-sectional area of rod (1) is 11 mm². The cross-sectional area of rod (2) is 14 mm2. For a uniformly distributed load of w = 4.1 kN/m, determine the length a so that the normal stress is the same in each rod. Assume L = 5.35 m. A (1) (2) a L. Answer: a = i m
PHILPS 2 Concepts EA/Documents/Week12 Compatibility 21-22-1%20(1).pdf 30 / 31 100% PROBLEM 2.35 The 1.35 m concrete post is reinforced with six steel bars, each with a 28 mm diameter. 450 mm Knowing that E, = 200 GPa and E, = 29 GPa, determine the normal stresses in the 1.35 m steel and in the concrete when a 1560 kN axial centric force P is applied to the post. [Ans. o = -59.5 MPa; o̟ = -8.63 MPa] Fig. P2.35 Seašon's Greetínas ·
The rigid beam BC is supported by rods (1) and (2). The cross-sectional area of rod (1) is 11 mm². The cross-sectional area of rod (2) is 15 mm². For a uniformly distributed load of w = 3.2 kN/m, determine the length a so that the normal stress is the same in each rod. Assume L = 5.60 m. A (1) B Answer: a = i L a D (2) m
Member (1) has an area of 2300 mm? and an allowable normal stress of 110 MPa. Member (2) has an area of 2000 mm? and an allowable normal stress of 180 MPa. Determine the maximum load P that may be supported by the structure without exceeding either allowable stress. (2) (1) 40 15°
The rigid beam BC is supported by rods (1) and (2). The cross-sectional area of rod (1) is 8 mm². The cross-sectional area of rod (2) is 17 mm². For a uniformly distributed load of w = 2.8 kN/m, determine the length a so that the normal stress is the same in each rod. Assume L = 4.20 m. (1) B Answer: a = i L W E 2
#2
The rectangular bar has a width of w = 3.50 in. and a thickness of t = 1.50 in. The normal stress on plane AB of the rectangular block shown is 6 ksi (C) when the load Pis applied. Assume a = 4 and b = 5. Determine (a) the magnitude of load P. (b) the shear stress on plane AB. (c) the maximum normal and shear stresses in the block at any possible orientation. P B Answers: (а) Р- i kips (b) Tự = i ksi (c) Omax = i ksi Tmax i ksi
A uniform cross section rod is composed of an aluminum section rigidly attached between steel and bronze sections. Axial loads are applied at the positions indicated.If P = 5.8 kN and the allowable stresses on the steel, aluminum and bronze are 40 MPa, 30 MPa and 25 MPa, respectively. Determine the minimum safe diameter for the rod. Answer: d= ___________________
A 10-mm diameter steel bolt is surrounded by bronze sleeve. The outer diameter of the bronze sleeve is 20 mm and its inner diameter is 10-mm. Given that the yield stress for the steel is 640 MPa and the yield stress for the bronze is 520 MPa, determine the magnitude of the maximum allowable total load that can be applied to this assembly. (Assume full bond between the steel and the bronze sleeve) Esteel = 200 GPa, Ebronze = 100 GPa, Factor of safety = 1.5
The rigid beam ABC is supported by a pin connection at C and by steel rod (1), which has a diameter of 12 mm. If the normal stress in rod (1) must not exceed 225 MPa, what is the maximum uniformly distributed load w that may be applied to beam ABC? Use dimensions of a = 350 mm, b = 700 mm, and c = 525.0 mm. Dot A Answer: W = ↓↓ a i 1 B W b (1) ↓↓ kN/m &
Rigid member AB is supported by hinge support at A and a 12-mm-diameter wire BC at B as shown. The diameter of the pin at A is 10 mm, thickness of member AB is 20 mm, and the thickness of each bracket of support A is 15 mm. Use a factor of safety FS= 2 and following failure stresses to determine the maximum load w (kN/m) the member can support. For wire BC: G=350 MPa Pin at A: Ta=200 MPa Support brackets: (Gharn n=150 MPa d-12 -35m 3m 20 mm smm Member AB- 10 mm Support Bracket- Support Bracket Conection detail at EpetA
The aluminum rod ABC (E =10.1* 106 psi), which consists of two cylindrical portions AB and BC, is to be replaced with a cylindrical steel rod DE (E =29 * 106 psi) of the same overall length. Deter-mine the minimum required diameter d of the steel rod if its vertical deformation is not to exceed the deformation of the aluminum rod under the same load and if the allowable stress in the steel rod is not to exceed 24 ks