(4) The shown cast-iron bracket has an ultimate compressive strength of 504 MPa and an ultimate tensile strength of 225 MPa. Given that the minimum material factor of safety needed is 1.5, it is required to: (a) Determine the maximum force P that can be supported by the bracket. (b) Draw the normal stress distribution at section ABD at this load value. 22 mm X 15 mm 15 mm

(4) The shown cast-iron bracket has an ultimate compressive strength of 504 MPa and an ultimate tensile strength of 225 MPa. Given that the minimum material factor of safety needed is 1.5, it is required to: (a) Determine the maximum force P that can be supported by the bracket. (b) Draw the normal stress distribution at section ABD at this load value. 22 mm X 15 mm 15 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pin-connected truss is loaded and supported as shown. Each aluminum member has a cross-sectional area of A = 3.6 in.?. Assume a = 4.75 ft and b = 5.7O ft. If the normal stress in each member must not exceed 55 ksi, determine the maximum load Pmax that may be supported by the structure. b Answer: Pmax = i kips
The lap joint is fastened by 5 one-inch diameter rivets. For P = 10 kips, determine (1.) the maximum shear stress in the joints, (2.) the maximum bearing stress in the rivets, and (3.) the maximum stress at section a-a.
Link BC is to be made of a steel for which the ultimate normal stress is 250 MPa. Determine the diameter of BC if the factor of safety is required to be 3.0. Assume that the link will be adequately reinforced around the pins at B and C. 1.25 kN/m 30° 5 m
The bell-crank mechanism is in equilibrium for an applied load of F₁ = 11 kN applied at A. Assume a = 300mm, b = 120mm, c = 75mm, and 0 = 40°. Pin B is in a double-shear connection and has a diameter of 23 mm. The bell crank has a thickness of 22 mm. Determine (a) the shear stress in pin B. (b) the bearing stress in the bell crank at B. Bell crank F₂ Support bracket F₁ Answers: Tpin B = i Ob = i a B MPa MPa
Determine the maximum normal stress developed in the bar when it is subjected to a tension of P = 4.3 kN given t=5 mm, a=5.5 mm, b=5 mm, F0.5 mm, and D=2.2 mm. [note: Drawing is not to scale] P O 275.20 MPa O 734.26 MPa O 172.00 MPa O 1915.45 MPa O 716.67 MPa O638.48 MPa O573.33 MPa O 677.58 MPa
The system shown to the right is made of two members, Member AC is completely rigid (it will not deform), and member BD is made from 6061-T6 AI Extrusion, has a length of 12", and has a cross sectional area of 2.0 in?. When a load of P=10,000 Ibs is applied, determine (a) the load in member BD, (b) the stress in member BD, (c) the strain in member BD, (d) the deflection of point B, (e) The lateral strain in member BD, and (f) the margin of safety for tension of member BD. 20". 15" A P.
number 3
answer letters D, E, and F only
The solid circular rod has a cross-sectional area of 360 mm². It is subjected to a uniform axial distributed loading along its length of w= 8 kN/m. Two concentrated loads also act on the rod: P = 7 kN and Q = 3 kN. Determine the normal stress in the rod at x = 0.1 m. Assume a=0.4 m and b = 1.3 m. a B b
- The bell-crank mechanism is in equilibrium for an applied load of F₁ = 15 kN applied at A. Assume a = 270mm, b = 170mm, c 70mm, and 9 50°. Pin B is in a double-shear connection and has a diameter of 20 mm. The bell crank has a thickness of 34 mm. Determine the bearing stress in the bell crank at B. Answer in MPa rounded-off to 2 decimal places. F₁ Bell crank Support bracket a B b
Current Attempt in Progress The solid 1.35-in.-diameter rod is subjected to a uniform axial distributed loading along its length of w =775 lb/ft. Two concentrated loads also act on the rod: P= 2500 lb and Q = 800 lb. Assume a = 11 in. and b = 22 in. Determine the normal stress in the rod at the following locations: (a) x = 7 in. (b) x = 21 in. w a Answer: Ox=7in. = i psi Ox=21in. i psi
The bell-crank mechanism is in equilibrium for an applied load of F₁ = 12 kN applied at A. Assume a = 250mm, b = 170mm, c = 80mm, and 0 = 50°. Pin B is in a double-shear connection and has a diameter of 20 mm. The bell crank has a thickness of 25 mm. Determine (a) the shear stress in pin B. (b) the bearing stress in the bell crank at B. Support bracket A Answers: Tpin B = i Ob= i Bell crank a B b MPa MPa