Determine the shearing stress at the Neatural axis (N.A.) Two 20 x 100-mm and two 20 × 180-mm boards are glued together as shown to form a 120 x 200-mm box beam.Know that the beam is subjected to a vertical shear of 3.625 kN.20 mm -100 mm -180 mm20 mmDDetermine the average shearing stress in the glued joint at A.The average shearing stress is|kPa.

Answered: Image /qna-images/answer/339b81a9-5174-44d2-a9b2-7d2fa6b28de9.jpg

Two 20 x 100-mm and two 20 × 180-mm boards are glued together as shown to form a 120 x 200-mm box bear Know that the beam is subjected to a vertical shear of 3.625 kN. 20 mm - 100 mm - 180 mm 20 mm D Determine the average shearing stress in the glued joint at A. The average shearing stress is |kPa.

Two 20 x 100-mm and two 20 × 180-mm boards are glued together as shown to form a 120 x 200-mm box bear Know that the beam is subjected to a vertical shear of 3.625 kN. 20 mm - 100 mm - 180 mm 20 mm D Determine the average shearing stress in the glued joint at A. The average shearing stress is |kPa.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1.) Solve for the shear and moment diagram 2.) Identify the minimum tensile and compressive bending stress values and location (from A).
4. A force Q is applied to a rectangular member with a size of 3oomm x 450mm. Q is located 37-5mm left and 6omm north of the center of gravity and induces a stress of 1.75 MPa compression at point A. a) What is the axial load at Q in kN b) What is the stress induced at point C & D in MPa A B
The box beam has an allowable bending stress of o= 10 MPa and an allowable shear stress of 7=775 kPa. Determine the maximum intensity w of the distributed loading that it can safely support. Also, determine the maximum safe nail spacing for each third of the length of the beam. Each nail can resist a shear force of 200 N. 30 mm 250 mm 30 mm 150 mm 30 mm 6m
A timber frame or truss shown below supports a load P of 50 kN. Find (a) the normal stress in all the members, (b) the horizontal shearing stress at the notched ends of timber AC, and the bearing stress of C on plate D that measures 0.25 m x 0.25 m x 0.025 m. P = 50 KN B 0.17 m 30° 0.15 m 10 0.25 m 0.1 m につく 0.25 m
A simply supported wood beam that is 13.2 m long carries a 41 kN concentrated load at B. The cross-sectional dimensions of the bearn are b = 125 mm, d = 350 mm, a = 110 mm, and c= 35 mm. Section a-a is located at x= 2.2 m from B. (a) At section a-a, determine the magnitude of the shear stress in the beam at point H. (b) At section a-a, determine the magnitude of the shear stress in the beam at point K. (c) Determine the maximum horizontal shear stress that occurs in the beam at any location within the entirespan. (d) Determine the maximum tensile bending stress that occurs in the beam at any location within the entire length. P. a H a a B C K 2L 3 3 Answer: (a) TH = i 689 КРа (b) TK = i КРа 280 (c) Tmax= i 799 kPa (d) Omax= 47.11 MPa
A long shaft of diameter d is subjected to twisting moment T at its ends. The maximum shear stress acting is equal to A zero B с D 16T d³ 32T +d³ 64T +³
Review: Design of simple structures 1. *1-96. Determine the required cross-sectional area of member BC and the diameter of the pins at A and B if the allowable normal stress is allow 3 ksi and the allowable shear stress is allow = 4 ksi. 1500 lb -2 ft -4 ft- 1500 lb B 60°
ACTIVITY Compute for the shearing stress in the pin at B for the member supported as shown in the figure. The diameter of the pin is 20mm. K.R.R.P. 00 Pin at B 200 mm- 40 KN AL B 250 mm
3. The beam is subjected to a shear of V-4 kN. Detemine the average shear stress developed in each nail if the nails are spaced 100 mm apart on each side of the beam. Each nail has a diameter of 4 mm. 100 mm 25 mm mm 75 mm mm 75 mi -75 nm 25 mm
At a point 8ft from D, solve the shear stress 4in from the top of the cross-section. The cross section is 6in by 18in. 16 k 2 k/ft 8k 3 k/ft B -12 ft 8 ft-+9 ft- 12 ft +-9 ft- 4 ft 3 ft 3 ft O 16.46psi O 65.84psi O 8.23psi O 32.92psi
The uniform beam is supported by two rods AB and CDthat have cross-sectional areas of 10-mm2 and 15-mm2,respectively. Determine the stress on two rods AB and CDif the uniform load is 5N/m.
1. Calculate the moment of inertia of the section in mm . 2. Calculate the location of the neutral axis from the bottom of the beam in mm. 3. Calculate the maximum moment in the beam in kN.m. 4. Calculate the flexural stress at a section 75mm from A and 40mm from the bottom of the beam in MPa. 5. Calculate the maximum compressive flexural stress of the beam in MPa. 6. Calculate the maximum tensile flexural stress of the beam in MPa. NOTE: Kindly answer all numbers with complete solution please. Needed ASAP.