tubular steel [G = 80 GPa] shaft is being designed to transmit 150 kW at 30 Hz. The maximum shear stress in the shaft must not exceed 80 MPa and the angle of twist is not to exceed 6° in a 4-m length. Determine the minimum permissible outside diameter if the ratio of the inside diameter to the outside diameter is 0.80.

tubular steel [G = 80 GPa] shaft is being designed to transmit 150 kW at 30 Hz. The maximum shear stress in the shaft must not exceed 80 MPa and the angle of twist is not to exceed 6° in a 4-m length. Determine the minimum permissible outside diameter if the ratio of the inside diameter to the outside diameter is 0.80.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

8.4 (A). A hollow shaft has to transmit 6 MW at 150 rev/min. The maximum allowable stress is not to exceed 60 MN/m² nor the angle of twist 0.3° per metre length of shafting. If the outside diameter of the shaft is 300 mm find the minimum thickness of the hollow shaft to satisfy the above conditions. G = 80 GN/m² [61.5 mm.]
The steel alloy shaft having a diameter of 38 mm is used to transmit torque, T as shown in Figure Q2(c). If the allowable shear stress of the shaft is 88kPa (i) Determine the maximum torque T that can be transmitted by the shaft. (ii) What would be the maximum torque T' if a 25 mm diameter hole is bored through the shaft? (iii) Sketch the shear-stress distribution along a radial line in each case. T Figure Q2(c)
A solid stainless steel [G = 108 GPa] shaft that is 1.2 m long will be subjected to a pure torque of T = 82 N-m. Determine the minimum diameter d required if the shear stress must not exceed 40 MPa and the angle of twist must not exceed 4.7°. Report both the maximum shear stress 7 and the angle of twist at this minimum diameter. Answers: d = mm. T = IN i MPa. i
A solid 1.500-in.-diameter steel [G = 11,000 ksi] shaft is subjected to torques TB = 190 lb-ft and TD= 140 lb-ft, acting in the directions shown. Assume a = 42 in., b = 72 in., and c = 36 in. If the allowable shear stress in the shaft is 20 ksi, determine the maximum torque TC that can be applied to the shaft.
A hollow steel propeller shaft is to transmit 4.5 MW at 3 Hz without exceeding a shearing stress of 50 MPa or twisting through more than 1deg in a length of 26 diameters. Compute the proper diameter if Do =2Di. Show your complete solution.
2) A shaft of a diameter of 30 mm is transmitting 14,9 kW at 400 rpm. The shaft is connected to a pulley of an axial length of 160 mm with the help of a rectangular key 16 mm x 12 mm ( b=16 mm, t=12mm). (The spokes are connected to the pulley, but the pulley is not shown in the figure). Axial length of the key, hub and pulley are 160 mm. Determine the shear and normal stresses developed in the rectangular key. Rectangular key Spokes A R Hub Shaft
A simple diagram of a driveshaft ABC is shown in Figure 3. The power generated by an engine is transmitted via the drive shaft, ABC. The section AB is a solid circular shaft 0.7 m long and the section BC is a hollow circular shaft 1.0 m long with 110 mm outer diameter and 55 mm inner diameter. Both shafts are made from a metal alloy (Shear Modulus G = 95 GPa). 0.7 m 1.0 m A в 2400 hp @ 2000 rpm Figure 3 a) If the drive shaft rotates at 2000 rpm and the power transmitted along the shaft is 2400 hp (1 hp = 745.7 W), calculate the torque developed in the drive shaft.
A solid shaft 5 m long is stressed to 60 MPa when twisted through 4 deg . Using G = 83 GPa, what power (Hp) can be transmitted by the shaft at 20 rps?
A steel shaft is to transmit 4.5 MW at 3 Hz without exceeding a shearing stress of 50 MPa or twisting through more than 10 in a length of 26 diameters. Compute the proper diameter if G = 83 GPa. [Note: Attach your solution] %3D
A solid steel [G= 12900 ksi] shaft with the diameter of d = 1.375 in. is subjected to torques TB = 250 lb.ft, TC = 300 lb.ft, and TD = 140 lb.ft, acting in the directions shown in the figure. Assume a = 48 in., b = 74 in., and c = 40 in. Determine the rotation angle of pulley C with respect to the support at A. In rad
A solid shaft 5 meters long is stressed to 55 MPa when twisted through 4 degrees. If G = 83 GPa. compute the shaft diameter in mm. What power in kW can be transmitted at 1200 rpm? O 59160.27 O 1155.74 O 44133.56 O 1160.60
2. Justify the simplification of this problem to only modeling one-eighth of the cross section 3. Construct two-dimensional elements grid (i.e., grid/mesh region), make the correct numbering and labeling of the nodes and elements.