True or False? The double-offset plunging-style CV joint uses a cylindrical outer housing with straight grooves and a cross groove joint.

Q: Can someone do a a static force analysis on this? Like method of joints sort of thing. Forgot how…

A: Static force analysis is done to do the analysis of the structure  and to check what will be the…

Q: 6-34. Determine the force in members DE, DF, and GF of the cantilevered truss and state if the…

A: The truss system is given by.Determine the force in members DE, DF, and GF.

Q: Longitudinal joint `Girth joint

A: GIVEN DATA- LONGITUDINAL JOINT STRENGTH 500KN/m GIRTH JOINT STRENGTH 220KN/m PRESSURE P=2MPa WE HAVE…

Q: Removable joints can be made by using welding. Select one: True False

A: In welding processes, the joining materials are heated above the recrystallization temperature, and…

Q: 80 kN MATHalino.com MATHalino.com 1 m 1 m 1 m 0.75 m

A:

Q: In this pair number of binary joint is available. O A. four O B. one O C three O D. two

A: A joint is the connection of two or more links at a section. In a fixed or permanent mechanical…

Q: (d) Calculate the mobility using the Kutzbach revision of Gruebler equation. Note: You can watch an…

A: The below figure shows the list of links, joints and higher pairs in the given linkage.The numbers…

Q: Draw the Mohr Circle and mark important points for a rod under pure tensile load & torsion

A:

Q: - What is mean by M24 X 2-RH 2-What is the function of a cover plate in riveted joints? 3- If a weld…

A: Given : M24 X 2-RH

Q: separately

A:

Q: Load  applied tangentially across the resisting section is Select one: Buckling Tensile…

A: Shear Stress When two equal and opposite forces are applied tangentially across the resisting…

Q: Which type of joint has a flatter design than anyother?a. Double-offsetb. Discc. Cross grooved.…

A: The cross groove joint uses balls and V-shaped grooves mostly on inner and outer races to cater the…

Q: Bolts and nuts are used for joining process. Select one: True False

A: Metal joining is defined as joining of two metal parts either temporarily or permanently with or…

Q: PROBLEM 4 1/ A 10 5! 21c B √³5' C P 10: D. S'E 10 5' LL. F

A: what are the forces in the members? (with using method of sections or method of joints.)

Q: Temporary joint is obtained by one of the following. (A) Interference fit (B) welding (C) Riveting…

A: Given data Temporary joint is obtained by one of the following

Q: Consider the stress-strain diagram, shown in the figure, of a bar made from a composite material.…

A: Young's modulus is the slope of the stress and strain curve up to the elastic limit.

Q: Consider the single-cup coffee maker shown below. (a) How many links (L) are there? Number the links…

A: (a) How many links (L) are there? Number the links starting with 1 (don't forget the "ground"…

Q: Lap Joint Questions The following questions all use this figure. Assume a bolt will be put in each…

A: Given: To find: Number of fasteners counted  for calculating area of net cross section.

Q: For the trus loaded and supported as shown, compute The force on each member. Again, tabulate your…

A:

Q: bolt tension force is 85% of its capacity. Use LRFD. cach) with a bolt spacing and gage distance of…

A: No of bolts = 8 Bolt dia d = 22 mm Bolt hole dia do = 25 mm Pitch distance p = 100 mm Gauge distance…

Q: Part of the screw thread connecting the adjacent flank on the bottom of the screw thread is known as…

A: Crest - In the top portion, it joins the sides of the thread. Root - in the bottom portion it joins…

Q: A constant velocity joint that is capable of in-and-out movement is a:   Select one: a. both…

A: Constant velocity (CV) joints are those joints that can facilitate the transmission of power from…

Q: 7. Determine the force in each member of the truss shown. State whether each member is in tension or…

A: The truss is symmetric with symmetric loading conditions, which means we have to solve half the…

Q: Determine the number of pin joints 4. Which of the following has multiple degrees of freedom? OOO

A:

Q: What is the complete specification of a nut having a stress area of 0.170 in? (standard size) that…

A: 1/2"-28UNEF-3B-LH

Q: The given frame is subjected to the applied loads P and Q. Note that members ABC and CDE are…

A: