A constant velocity joint that is capable of in-and-out movement is a:   Select one: a. both fixed joint and inboard joint b. inboard joint c. fixed joint d. plunge joint

Q: Analyze the truss using methods of joints

A:

Q: swer the following: 1) Define the degree of freedom of a joint? 2) How many degrees of freedom does…

A: To define: 1) Define the degree of freedom of a joint?2) How many degrees of freedom does a c-joint…

Q: 6-34. Determine the force in members DE, DF, and GF of the cantilevered truss and state if the…

A: The truss system is given by.Determine the force in members DE, DF, and GF.

Q: Calculate the degree of freedom, point out the positions if there are multiple joints, high-pair and…

A:

Q: Longitudinal joint `Girth joint

A: GIVEN DATA- LONGITUDINAL JOINT STRENGTH 500KN/m GIRTH JOINT STRENGTH 220KN/m PRESSURE P=2MPa WE HAVE…

Q: Removable joints can be made by using welding. Select one: True False

A: In welding processes, the joining materials are heated above the recrystallization temperature, and…

Q: Pre-tensioning of a bolted joint is used to (a) strain harden the bolt head (b) decrease stiffness

A: Given: Pre-tensioning: When nut is tighten against the bolt, a compressive force is induced in…

Q: 80 kN MATHalino.com MATHalino.com 1 m 1 m 1 m 0.75 m

A:

Q: 2) For a bolted tension member with a lap splice as shown, what are all the limiting tension…

A: Given data, A single strip butt joint is given in the figure. n= No o rivets = 4 To show, all the…

Q: (d) Calculate the mobility using the Kutzbach revision of Gruebler equation. Note: You can watch an…

A: The below figure shows the list of links, joints and higher pairs in the given linkage.The numbers…

Q: Please select all that applies. The possible failure modes for bolted joints are: shear in the bolts…

A: To select: The correct options. Concept used: Failure of the bolted joints: The bolted joints may…

Q: Calculate the degree of freedom of the mechanism shown in figure. O a. 2 O b. 1 O c.-1 O d. 0

A:

Q: QUESTION: Suppose a bolted tension used in a doube-D ring configuration is properly preloaded. The…

A: given; ⇒spring constant for the bolte (k1)=7.8MN/m⇒spring constant for the member…

Q: Which type of joint has a flatter design than anyother?a. Double-offsetb. Discc. Cross grooved.…

A: The cross groove joint uses balls and V-shaped grooves mostly on inner and outer races to cater the…

Q: Bolts and nuts are used for joining process. Select one: True False

A: Metal joining is defined as joining of two metal parts either temporarily or permanently with or…

Q: For applying the method of joint at joints the forces need to be concurrent؟ Select one: True False

A: In method of joints, all forces are concurrent. So, by applying equilibrium equation ( in x and y…

Q: PROBLEM 4 1/ A 10 5! 21c B √³5' C P 10: D. S'E 10 5' LL. F

A: what are the forces in the members? (with using method of sections or method of joints.)

Q: Temporary joint is obtained by one of the following. (A) Interference fit (B) welding (C) Riveting…

A: Given data Temporary joint is obtained by one of the following

Q: Consider the single-cup coffee maker shown below. (a) How many links (L) are there? Number the links…

A: (a) How many links (L) are there? Number the links starting with 1 (don't forget the "ground"…

Q: Calculate external support reactions, forces of internal joints and draw FBD of assembly

A:

Q: True or False? The double-offset plunging-style CV joint uses a cylindrical outer housing with…

A: Double-offset plunging style CV joint :

Q: A ball and a socket joint forms a

A: A ball and a socket joint is a form of synovial joint in which socket swivel around the fixed ball.…

Q: 7. Determine the force in each member of the truss shown. State whether each member is in tension or…

A: The truss is symmetric with symmetric loading conditions, which means we have to solve half the…

Q: 4. Briefly explain the two designs of tie rod ends and describe their function

A:

Q: What is a two-force member? Illustrate schematically.

A: This question is based on the concept of two force member.

Q: va three DoF (Degree of freedom) eight link (n=8) mechanism with rev rify DoF mechanism using…

A:

Q: Apply shape optimization analysis to make lightweight cotter joint.

A: INTRODUCTION : Cotter joint is used to connect two rods when it is subjected to the tensile or…

Q: Frames multi-force member(s)

A: To define: A frame has how many multi force member

Q: The given frame is subjected to the applied loads P and Q. Note that members ABC and CDE are…

A:

Joining Processes

It is the process of permanent or temporary joining of two metal pieces with the help of heat or pressure. Two metal parts are assembled by applying an energy source for the formation of a single unit. The obtained joined metals cannot be fragmented easily with the application of any force.