Treat the following questions: 1- Calculate the intensity of the electrical current passing through a device that consumes 20,000 coulomb electrical charges within 10 minutes 2- Calculate the resistance of a copper wire, m long and of 2cm cross-section, knowing that the resistivity of copper p=1.6x10 -8 Ω.m. 3- An electric heater carrying a current of 5A, during 30 minutes under a voltage of 200V. Calculate: a- The resistance of the electric heater b- The power dissipated due to the heating effect c- The electric energy in kilo watt hour ( KWh ) d- The heat energy in joules and in calories 4- We have 4 resistors connected in series R1= 32 R2= 52 R3= 72 R4= 22 Under a voltage of 20V Calculate: a- Draw the circuit b- The total resistance Regg c- The intensity of current in the circuit d- The voltage at each resistor e- The power dissipated in the circuit

Treat the following questions: 1- Calculate the intensity of the electrical current passing through a device that consumes 20,000 coulomb electrical charges within 10 minutes 2- Calculate the resistance of a copper wire, m long and of 2cm cross-section, knowing that the resistivity of copper p=1.6x10 -8 Ω.m. 3- An electric heater carrying a current of 5A, during 30 minutes under a voltage of 200V. Calculate: a- The resistance of the electric heater b- The power dissipated due to the heating effect c- The electric energy in kilo watt hour ( KWh ) d- The heat energy in joules and in calories 4- We have 4 resistors connected in series R1= 32 R2= 52 R3= 72 R4= 22 Under a voltage of 20V Calculate: a- Draw the circuit b- The total resistance Regg c- The intensity of current in the circuit d- The voltage at each resistor e- The power dissipated in the circuit

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Include an illustration of the circuit in the solutions. Thank you
1- Some copper wire has a resistance of 200 at 20°C. A current is passed through the wire and the temperature rises to 90°C. Determine the resistance of the wire at 90°C, correct to the nearest ohm, assuming that the temperature coefficient of resistance is 0.004/°C at 0°C
Question 3 a. Some materials exhibit the property of superconductivity under certain conditions. State what is meant by superconductivity and explain the required conditions for the material to become superconducting. b. The diagram below shows the cross-section of a cable consisting of parallel filaments that can be made superconducting, embedded in a cylinder of copper. copper cylinder filament The cross-sectional area of the copper in the cable is 2.28 x 10-7 m². The resistance of the copper in a 1.0 m length of the cable is 0.075 N. Calculate the resistivity of the copper, stating an appropriate unit. State and explain the what happen to the resistance of the cable when the embedded filaments of wire are made superconductive? i.
3 Please follow this format: Given Formula Substition Thanks!
2. What is the resistance at normal room temperature of 80 m of copper wire having a diameter of 0.64 mm? (Bcopper 1.7241 x 10-8 0- m at 20 °C). 3. A lightning bolt strikes an airplane with 3OKA for 2ms. How many Coulombs of charge are deposited on the plane?
A coil of copper wire has a resistance of 90 N at 20°C and is connected to a 230 V supply. By how much must the voltage be increased in order to maintain the current constant of the temperature of the coil rises to 60°C? Take the temperature coefficient of resistance of copper as 0.00428 from 0°C.
An aluminum wire 5m long and 2mm diameter is connected in parallel with a copper wire 3m long. The total current is 4 A and that in the aluminum wire is 2.5 A. Find the diametre of the copper wire. The resistivity of copper wire being 1.7 micro ohm meter and that of aluminum taken Al 2.6 micro ohm meter
Answer the following questions with True or False
Describe the following I-V graph of the components below based on the difference of ohmic and non-ohmic materials.
1. Given a typical tungsten filament of a light bulb, 1 m long and 0.05mm in radius. nim B. Given that the temperature resistivity coefficient of tungsten is 4.5 X 10-3/ °C, meldoig zinovovd omo A. Calculate the typical resistance of the filament given that its resistivity at 20 °C is 5.6 X 10-8 (Q -m). calculate the resistance at 2000 °C. assuming linear resistivity-temperature 2000 ert pria relation.
A coil consists of 5000 turns of copper wire having a circular - section of diameter 0.0045 m. The mean length per turn is 0.8 m and the electrical resistivity of copper is 0.03 μΩ–m. Determine the resistance of the coil in μΩ.
The resistivity of a ferric-chromium-aluminum alloy is 51x10° ohm-meter. A sheet of the material is 15 cm long, 6 cm wide and 0.014 cm thick. Determine the resistance between a) opposite ends and b) opposite sides.