To test the affordable pressure of the product, an engineer produced the below formula: P = 1²G¬1C=1 Where I is the surface energy intensity per unit time, G is measured in J/m2s and c is the speed of the production line in m/s. 1. Verify the validity of the equation. 2. If the applied energy is 0.01 J and the speed is 5.7m/s, t is 0.01 sec and A =0.117 inch2 calculate P, I, and G. 3. Using the above formula, produce a formula relating P to E (energy). Discuss the new relation and how it varies with its parameters.

To test the affordable pressure of the product, an engineer produced the below formula: P = 1²G¬1C=1 Where I is the surface energy intensity per unit time, G is measured in J/m2s and c is the speed of the production line in m/s. 1. Verify the validity of the equation. 2. If the applied energy is 0.01 J and the speed is 5.7m/s, t is 0.01 sec and A =0.117 inch2 calculate P, I, and G. 3. Using the above formula, produce a formula relating P to E (energy). Discuss the new relation and how it varies with its parameters.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

: | %85 || 2 100 Q1/ Two Forces Shown in Fig. (1) acts on the bracket, determine the effect of these two forces (using Parallelogram method). 150N F₁-200 N ||| Mech. eng. 1st atte - - ٩:٣٤ 71 ينة تكرير النفط والغاز | الدراسات الصباحية ندسة العمليات النفطية
As a mechanical engineer, you were asked by your supervisor to monitor the operation of 4-stroke engine; as a result you got the following readings: > Imep = 780 kN/ m2 > Engine speed = 800 rpm > Brake Power 30 kW %3D %3D > nm = 85 % > B/S 0.7 You noticed also, that the inlet valve opens 10° before TDC and closes40° after BDC and it takes 0.0035 second after ignition for the charge to gain maximum pressure. Depending on the above readings, find the following engine parameters: a. The crank angle when the spark occursfor the maximum pressure to be at TDC b. The time period in second of inlet valve opening during one cycle c. The diameter of the engine d. The average piston speed 1 Upload file
1 The following observations are recorded during a test on a four-stroke petro engine, F.C = 25cc of fuel in 10 sec, speed of the engine is 2600 rpm, B.P = 22 kW, Qair 0.00134 m, piston diameter 90 mm, density of the fuel = 0.85gm/cc , compression ratio = 7.5, CV of fuel = 42000KJ/Kg, room temperature = 24 °C %3D = 140mm, stroke length = %3D %3D %3D 2 A six-cylinder 4-stroke cycle petrol engine is to be designed to develop 250 kW of (b.p) at 2200 rpm the stroke / bore ratio is to be 1.3:1. Assuming nm =80% and an indicated mean effective pressure of 9.5 bar, determine the required bore and stroke. If the compression ratio of the engine is to be 7.5 to 1, determine consumption of petrol in kg/h and in kg/bp.hr. Take the ratio of the indicated thermal efficiency of the engine to that of the constant volume air standard cycle as 0.65 and the calorific value of the petrol as; 44770KJ/kg.
Please show system sketches and related energy flows for all problems. 1.1 Determine the electrical power supplied to a boiler when the temperature of the entering water is 20 C and the exiting temperature is 89 C. The flow of the pressured water is 2 Kg/s. There is a negligible pressure drop through this boiler and it operates at a constant pressure of 3 bars. The specific heat is c = 4,370 J/(Kg K). There is a 1.5(105 ) W rate of heat loss from the boiler during this process to a surrounding at 293.2 k. Consider steady state conditions. 1.4 Calculate the mass flowrate of fuel (natural gas, CH4) required to heat the water flow to the conditions of problem 1.1 if the electrical heating device is replaced with a gas fired boiler. The high heating value (HHV) of the fuel is 50.02 MJ/kg. 1.5 Calculate the exergy destroyed in the process described by problem 1.4. The exergy of the fuel entering this process is 51.82 MJ/Kg. The dead state temperature is 293.2 K and pressure is 1 bar. The…
2) An object starts from rest at time t = 0.00 s and moves in the +x direction with constant acceleration. The object travels 15.0 m from time t = 1.00 s to time t = 2.00 s. What is the acceleration of the object? %3D %3D
2. Show, with sketches, the differences between the shear stress of solids and fluids when subjected to a tangential force. 3. Is there any concern that blood flow in the human retina will become turbulent? If the blood density is 1060 kg/m³, the inside diameter of the arteriole is 0.0075 cm, the mean velocity in the vessel is 3 cm/s, and the viscosity measured as 0.00349 Ns/m².
Hi! Pleaseee answer with complete solution, pv and ts diagrams. Thanks!! ❤️
***Solve the following problems, correctly and systematically, and show all the necessary figures. Show your complete solutions neatly. Thank you!*** A single-stage centrifugal pump having a suction pipe 254 mm in diameter and a discharge pipe diameter of 5 inches is being tested and found to discharge 48 lps of water. A pressure gage connected to the inlet pipe reads 118 mm Hg vacuum and a discharge gage reads 150 kPa at a distance 100 cm above the point where the inlet pressure was measured. If the kW rating of the driving motor is 12 kW, calculate: a) the pump efficiency. b) if this pump runs at 1800 rpm, what will be the new discharge rate, head, and power developed if the pump speed was increased to 3600 rpm? Assume constant efficiency. c) Determine the pump type.
49 lll all a ۸:۳۰ م ۲ ۱۲ك. ب/ث © Test 3.pdf > F1 F2 a C F3 A BI d b F4 E B Consider the following values: - F5 a = 12 m; b = 10 m; c = 10 m; d = 8 m; F1 = 6 kN; F2 = 7 kN; F3 = 8 kN; F4 = 9 kN; F5 = 10 kN; a = 30°, e = 45° , B = 60° 1] What is the resultant moment of the five forces acting on the rod about point A? a) - 111.6 kN.m b) 112.6 kN.m e) - 184.6 kN.m d) - 109.6 kN.m e) - 104.1 kN.m ) None of them 2] What is the resultant moment of the five forces acting on the rod about point B? a) -95.8 kN.m b) 42.7 kN.m e) 80.9 kN.m d) 10.9 kN.m e) 51.8 kN.m f) None of them 3] What is the resultant moment of the five forces acting on the rod about point C? b) - 21.1 kN.m c) 17.4 kN.m d) - 16.5 kN.m a) 32.6 kN.m e) 15.6 kN.m f) None of them 4] What is the resultant moment of the five forces acting on the rod about point D? a) 37.6 kN.m b) 73.8 kN.m e) 71.6 kN.m d) 52.1 kN.m e) 21.1 kN.m f) None of them 5] What is the moment of the force F2 about point E? a) 90.7 kN.m b) - 88.1 kN.m e) 54.6…
A company that produces x thousand A type and y thousand B type annually will have annual expenses C(x,y) = 5x2 – 4xy + 3y2 – 18x + 20 million TL and annual income R(x,y) = 8x + 5y million TL. How many thousand type A and how many thousand type B products should this firm produce annually to maximize its annual profit? What would be the maximum profit?
Please Answer the following question step-wise with detailed explanations. Thanks in advance?❤️