To maximize production and minimize pumping costs, crude oil is heated to reduce its viscosity during transportation from aproduction field.(1) Consider a pipe-in-pipe configuration consisting of concentric steel tubes with an intervening insulating material. The inner tube isused to transport warm crude oil through cold ocean water. The inner steel pipe (k, = 45 W/m-K) has an inside diameter of D₁, 1 =150 mm and wall thickness t; = 20 mm while the outer steel pipe has an inside diameter of D₁,2 = 250 mm and wall thicknessto = 1;. Determine the maximum allowable crude oil temperature to ensure the polyurethane foam insulation (k = 0.055 W/m-K)between the two pipes does not exceed its maximum service temperature of 7p,max = 70°C. The ocean water is at T, = -5°C andprovides an external convection heat transfer coefficient of h, = 500 W/m²K. The convection coefficient associated with the flowingcrude oil is h; = 450 W/m².K.(2) It is proposed to enhance the performance of the pipe-in-pipe device by replacing a thin (= 10 mm) section of polyurethanelocated at the outside of the inner pipe with an aerogel insulation material (k = 0.012 W/m-K). Determine the maximum allowablecrude oil temperature to ensure maximum polyurethane temperatures are below Tp. max = 70°C. Determine the convection heat transfer resistance on the inside of the pipe per unit length, in m-K/W.RLconv.iSave for LaterUsing multiple attempts will impact your score.20% score reduction after attempt 1Step 2m.K/WDetermine the conduction resistance of the polyurethane per unit length without the aerogel, in m-K/W.R't,cond.p =Step 3m-K/WSave for LaterUsing multiple attempts will impact your score.20% score reduction after attempt 1Attempts: 0 of 3 usedSave for LaterUsing multiple attempts will impact your score.Determine the conduction resistance of the polyurethane per unit length when aerogel is used, in m-K/W.Rº 1,cond.p.acm-K/WAttempts: 0 of 3 used Submit AnswerSubmit AnswerAttempts: 0 of 3 usedSubmit Answer

"Since you have asked Multiple questions, we will solve only the first question for you. If you want…

To maximize production and minimize pumping costs, crude oil is heated to reduce its viscosity during transportation from a production field. (1) Consider a pipe-in-pipe configuration consisting of concentric steel tubes with an intervening insulating material. The inner tube is used to transport warm crude oil through cold ocean water. The inner steel pipe (k, = 45 W/m-K) has an inside diameter of Di, 1 = 150 mm and wall thickness ; = 20 mm while the outer steel pipe has an inside diameter of D₁,2 = 250 mm and wall thickness to = t;. Determine the maximum allowable crude oil temperature to ensure the polyurethane foam insulation (k, = 0.055 W/m-K) between the two pipes does not exceed its maximum service temperature of Tp. max = 70°C. The ocean water is at T, = -5°C and provides an external convection heat transfer coefficient of h, = 500 W/m²-K. The convection coefficient associated with the flowing crude oil is h; = 450 W/m².K.

To maximize production and minimize pumping costs, crude oil is heated to reduce its viscosity during transportation from a production field. (1) Consider a pipe-in-pipe configuration consisting of concentric steel tubes with an intervening insulating material. The inner tube is used to transport warm crude oil through cold ocean water. The inner steel pipe (k, = 45 W/m-K) has an inside diameter of Di, 1 = 150 mm and wall thickness ; = 20 mm while the outer steel pipe has an inside diameter of D₁,2 = 250 mm and wall thickness to = t;. Determine the maximum allowable crude oil temperature to ensure the polyurethane foam insulation (k, = 0.055 W/m-K) between the two pipes does not exceed its maximum service temperature of Tp. max = 70°C. The ocean water is at T, = -5°C and provides an external convection heat transfer coefficient of h, = 500 W/m²-K. The convection coefficient associated with the flowing crude oil is h; = 450 W/m².K.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Dry, compressed air at Tm,i whose surface is at T; = 25°C. Determine the thermal entry length, in m, the mean temperature of the air at the tube outlet, in K, the rate of heat transfer from the air to the tube wall, in W, and the power required to flow the air through the tube, in W. For these conditions the fully developed heat transfer coefficient is h = 3.58 W/m2-K. Evaluate the properties of air at 320 K 75°C, p = 10 atm, with a mass flow rate of m = 0.003 kg/s, enters a 32-mm-diameter, 5-m-long tube i Tmo = i K P = i q =
To maximize production and minimize pumping costs, crude oil is heated to reduce its viscosity during transportation from a production field. (1) Consider a pipe-in-pipe configuration consisting of concentric steel tubes with an intervening insulating material. The inner tube is used to transport warm crude oil through cold ocean water. The inner steel pipe (k, = 45 W/m-K) has an inside diameter of D;1 = 150 mm and wall thickness t; = 20 mm while the outer steel pipe has an inside diameter of D; 2 = 250 mm and wall thickness to = tj. Determine the maximum allowable crude oil temperature to ensure the polyurethane foam insulation (k, between the two pipes does not exceed its maximum service temperature of T, max = 70°C. The ocean water is at T , = -5°C and provides an external convection heat transfer coefficient of h, = 500 W/m2-K. The convection coefficient associated with the flowing crude oil is h¡ = 450 W/m2-K. = 0.03 W/m-K) (2) It is proposed to enhance the performance of the…
Consider a 26-cm x 31-cm printed circuit board (PCB) that has electronic components on one side. The board is placed in a room at 20°C. The heat loss from the back surface of the board is negligible. Assume that the circuit board dissipates 8 W of power in steady operation. Take the emissivity of the surface of the board to be 0.8 and assume the surrounding surfaces to be at the same temperature as the air in the room. Evaluate air properties at a film temperature of 32.5°C and 1 atm pressure. Given: The properties of air at 1 atm and 32.5°C. k = 0.02067W/m.°C v= 1.631 x 10-5 m2/s Pr = 0.7275, B = 0.003273 K-1
Please quickly
please answer asap with clear solution
To maximize production and minimize pumping costs, crude oil is heated to reduce its viscosity during transportation from a production field. (1) Consider a pipe-in-pipe configuration consisting of concentric steel tubes with an intervening insulating material. The inner tube is used to transport warm crude oil through cold ocean water. The inner steel pipe (k, inside diameter of Di 1 50 W/m-K) has an = 150 mm and wall thickness t; = 20 mm while the outer steel pipe has an inside diameter of = 250 mm and wall thickness to = t¡. Determine the maximum allowable crude oil temperature to ensure the Di, 2 polyurethane foam insulation (kp temperature of T, 0.0675 W/m-K) between the two pipes does not exceed its maximum service = 70°C. The ocean water is at T o, 0 = -5°C and provides an external convection heat transfer р, таx coefficient of ho = 500 W/m2.K. The convection coefficient associated with the flowing crude oil is h; = 450 W/m2-K. (2) It is proposed to enhance the performance of…
Hot fluid "C= 2562 J/kg.k , Pr=51.3, µ = 5.22E-3 Pa.s, k= 0.260 W/m.K" flows at 1.3 kg/min inside a 3-mm diameter, thin- walled tube. The tube is coiled and submerged in a water bath maintained at 23°C. The fluid experiences a temperature drop of 60°C and leaves the tube at 35°C. What is the required length of the tube "m"? Neglect heat transfer enhancement associated with the coiling. Assume fully developed flow, if turbulent flow use Dittus-Boelter equation: Nu = 0.023 Re 0.8 Pr. Select one: A. 25.62 В. 35.27 C. 27.95 D. 30.61 E. 33.27
2. Engine oil (similar to oil C) flows at 1.2 ft/s through a 1-inch diameter tube. The bulk oil temperature is 190 F and the tube surface temperature is 210 F. Determine the unit convective coefficient for a tube length of 10 ft. If the tube length is doubled, what is the percentage increase (or decrease) in the film coefficient? Let k = 0.96 Btu-in/hr-ft2-F and c = 0.52 Btu/lb-F for the oil. *
To maximize production and minimize pumping costs, crude oil is heated to reduce its viscosity during transportation from a production field. (1) Consider a pipe-in-pipe configuration consisting of concentric steel tubes with an intervening insulating material. The inner tube is used to transport warm crude oil through cold ocean water. The inner steel pipe (k, = 45 W/m-K) has an inside diameter of D;, 1 = 150 mm and wall thickness t; = 20 mm while the outer steel pipe has an inside diameter of D;, 2 = 250 mm and wall thickness t, = t;. Determine the maximum allowable crude oil temperature to ensure the polyurethane foam insulation (kp = 0.03 W/m-K) between the two pipes does not exceed its maximum service temperature of T, max = 70°C. The ocean water is at T,o = -5°C and provides an external convection heat transfer coefficient of h, = 500 W/m²-K. The convection coefficient associated with the flowing crude oil is hị = 450 W/m²-K. (2) It is proposed to enhance the performance of the…
A 6" NB carbon steel pipe is used to convey super - heated steam at design pressure of 12 kg/cm2 and temperature of 300°C, determine the minimum thickness of the pipe required to the system need neat and clean correct handwritten solution
Please quickly
Hot fluid "C= 2562 J/kg.k, Pr=51.3, µ = 5.22E-3 Pa.s,k= 0.260 W/m.K" flows at 1.3 kg/min inside a 3-mm diameter, thin- %3| walled tube. The tube is coiled and submerged in a water bath maintained at 23°C. The fluid experiences a temperature drop of 60°C and leaves the tube at 35°C. What is the heat transfer rate "Watts"? Neglect heat transfer enhancement associated with the coiling. Assume fully developed flow, if turbulent flow use Dittus Boelter equation: Nu = 0.023 Re 0.8 Pr. Select one: А. 3630.4 B. 4196.6 C. 2964.2 D. 3930.1 Е. 3330.6