Answered: To determine the particle size…

Engineering

Civil Engineering

To determine the particle size distribution of fine and coarse aggregate by dry sieving.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: civil engg material

A: Gradation of Aggregate- It is defined as a process that helps in particle size distribution which is…

Q: What is the difference between conducting laboratory tests on the specific gravity and absorption of…

A: Step: 1 Aggregate materials: - It is defined as mixture of coarse and fine particles like concrete,…

Q: Coarse aggregate placed igid buc its unit weight. The following data were obtained: Volume of bucket…

A: According to given data Coarse aggregate is placed in a rigid bucket (mold) and rodded with a…

Q: Find the specific the surface in cm2/g of the fine aggregates knowing that its specific gravity is…

A: Given Data: The specific gravity of a fine aggregate is, G=2.65 g/cm3 The correction factor for all…

Q: A specific gravity test was performed on a sample of fine aggregate and produced the following…

A: To find Specific gravity of fine aggregates Classify aggregate on basis of surface texture

Q: The mass of fine aggregate B has been reduced and weighed to conduct an aggregate test shown in…

Q: Sieve analysis test for fine aggregates was performed on a sample of fine aggregates and produced…

Q: Based on the data shown in Table select the blend for a Superpave design aggregate structure. Assume…

Q: TEST PROCEDURE: 1. Dry the aggregate test sample to a constant weight at a temperature of 110 ±…

A: Note: Hi! Thank you for the question, As per the honour code, we are allowed to answer three…

Q: Calculate the percent voids between aggregate particles that have been compacted by rodding, if the…

A: Given that, Dry rodded unit weight of aggregate : γb=1161 kg/m3 ⇒72.5 lb/ft3 Bulk dry specific…

Q: Fine aggregate sample was tested to find its physical properties. The test results were as follows:…

A: Solution: Given Data Bulk specific gravity=2.42 Apparent specific gravity=2.58 Mass of vessel full…

Q: 1)Determine the uncorrected and corrected weights based on the following data using the traditional…

A: Following is required mix design procedure :

Q: 1. What is the unit weight of aggregate?

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: The nominal maximum size for an aggregate is the standard sieve opening immediately smaller than the…

A: Answer:- Nominal maximum size of an aggregate:- The smallest sieve opening through which the entire…

Q: Calculate the percent voids between aggregate particles that have been com-pacted by rodding, if the…

A: Given: Dry unit weight yd = 1161 kg/m3 Specific gravity G = 2.639 To find: Percentage voids e = ?…

Q: In designing concrete structures, normally maximum aggregate sizes are adopted with ranges from 10mm…

A: Greater the size of aggregate lesser is the surface area. Lesser is the surface area indicate that…

Q: Sieve size (mm) 10 5 2.36 1.18 0.6 0.3 0.15 0.075 Wt. retained (g) 0 7 30 33 62 98 55 18 Retained…

Q: Please provide

Q: Volume of measure, (ft³) Weight of measure (lb) Weight of measure + aggrega

Q: The fineness modulus is a relative measure of how coarse or how fine an aggregate sample is.…

A: The fineness modulus is a value that signifies the average value of particle size.

Q: Calculate the percent voids between aggregate particles that have been com- pacted by rodding, if…

Q: A sieve analysis test for fine aggregates was performed on a sample of fine aggregates and produced…

A: The given data is shown below:

Q: A sample of coarse aggregate is placed in a bucket of know volume (0.5 ft^3) and rodded with a…

A: Volume of bucket = 0.5 ft3Empty weight of the bucket = 20.3 lb

Q: choose true or false 2.68, 2.72 and 2.7 is the true order of bulk specific gravity, apparent…

A: True

Q: Three samples of fine aggregate have the properties shown below. Determine in percentage: (a) total…

A: MeasureSampleABCWet Mass (g)521.0522.4523.4Dry Mass (g)491.6491.7492.1Absorption…

Q: 5.10 Samples of coarse aggregate from a stockpile are brought to the laboratory for determination of…

A: Given:- The following weights are found from the sample of coarse aggregates:- Mass of moist…

Q: : What is meant by: 1. absorption, 2. Moisture content (MC), 3. Bulk density of aggregate,

A: 1. Adsorption- It is surface phenomena, It is the adhesion of atoms, molecules or ions from a…

Q: What should be the observation and analysis for sieve analysis of fine aggregate if the value of…

A: Fineness Modulus 3.7 Cu= 4.1 Cc= 1.1 % error = 1.8% Cu= 4.1 between 4-6 Hence well graded sand Cc=…

Q: Sieve Size Amount Retained, Ib 3 in. 2 in. 1-1/2 in. 3.7 1 in. 15.9 3/4 in. 12.0 1/2 in. 13.5 3/8…

Q: SIEVE NO AMOUNT RETAINED (g) 4 33 8 42 10 14 30 164 40 73 100 159 200 20 PAN 31

Q: Differentiate between Scalar Aggregate and Vector Aggregate

A: Vector Aggregate- An aggregate which is associated with a group clause (even if the group by list is…

Q: 2) How should the moisture contents of the three samples compare? 3) Why is it important to…

A: 2) The moisture content of three samples can be compared by using oven dried method. In this method…

Q: if my Fineness modulus for fine aggregates is 1.88, does it meet the standards fineness modulus for…

A: Fineness modulus is defined as summation of aggregate of cumulative percentage of particles retained…

Q: Laboratory specific gravity and absorption tests are run on two coarse aggregate sizes, which have…

Q: Fine aggregate sample was tested to find its physical properties. The test results were as follows:…

A: Solution: Given Data: Bulk specific gravity=2.42 Apparent specific gravity=2.58 Mass of vessel full…

Q: Sieve analysis for fine and coarse aggregate is done, how can we say that those samples are good and…

A: The fineness modulus is the total of the cumulative percentage that stayed on the each sieve from…

Question

To determine the particle size distribution of fine and coarse aggregate by dry sieving.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1 Introduction:-

VIEW

Step 2 Theory:-

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

What is the method of compaction used in bulk unit weight and voids in aggregate?
5.14 Coarse aggregate is placed in a rigid bucket and rodded with a tamping rod to determine its unit weight. The following data are obtained: Volume of bucket = ¹/2 ft³ Weight of empty bucket = 20.3 lb Weight of bucket filled with dry rodded coarse aggregate: Trial 176.6 lb Trial 275.1 lb Questions and Problems 217 Trial 3 78.8 lb a. Calculate the average dry-rodded unit weight b. If the bulk dry specific gravity of the aggregate is 2.620, calculate the percent voids between aggregate particles for each trial.
I need right solution with clear calculation
pls answer soon
Laboratory specific gravity and absorption tests are run on two coarse aggregate sizes, which have to be blended. The results are as follows: Aggregate A: Buck specific gravity = 2.395; absorption = 4.69% Aggregate B: Buck specific gravity = 2.601; absorption = 0.51% What is the specific gravity of a mixture of 50]% aggregate A and 50% aggregate B by weight?
A sieve analysis test was performed on a sample of coarse aggregate and produced the following results:A.) Calculate the fineness modulus of aggregate? Is in within the typical range?
What is maximum capacity of measure should be used in determining the density of the concrete if the nominal maximum aggregate size of coarse aggregate is 25.0 mm?
31
Is it correct to say that the fineness modulus of aggregate B is 0.44 asumming aggregate B is a fine aggregate and also that the percent passing the 1.18mm, No. 16 sieve is 56%?
Table 1 shows the sieve analysis of a 900-g fine aggregate samples. (c) Identify which aggregate is (i) open graded (ii) gap graded and (iii) dense graded. Justify your answer.
Calculate the percent voids between aggregate particles that have been compacted by rodding, if the bulk dry-rodded unit weight is 90 lb/ft3 and the bulk dry specific gravity is 2.70.
Sieve analysis test for fine aggregates was performed on a sample of fine aggregates and produced the following results: a. Calculate the percent passing through each sieve.b. Plot the percent finer in a semi-log gradation chart.c. What is the maximum aggregate size of the sample?d. What is the nominal maximum aggregate size of the sample?e. What is the fineness modulus? Is it in typical range?