Analysis of Fine AggregatesFill in the table: SIEVE NOAMOUNT RETAINED (g)433842101430164407310015920020PAN31 CUMULATIVECUMULATIVESIEVEAMOUNTAMOUNTPERCENT RETAINED,PERCENT PASSINGSIZERETAINED, g (a)RETAINED,g (b)(c)=(b)*100/TOTAL(d)=100 - ( c )TOTAL

Answered: Image /qna-images/answer/9212ff28-078f-4893-903b-1adc2c5d3ab4.jpg

Answered: SIEVE NO AMOUNT RETAINED (g) 4 33 8 42…

Engineering

Civil Engineering

SIEVE NO AMOUNT RETAINED (g) 4 33 8 42 10 14 30 164 40 73 100 159 200 20 PAN 31

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The use of rather than irregularly shaped aggregate also give - workability. * Smooth surfaces give…

A: Option 1 and 3 is correct.

Q: Well graded aggregate means sizes within the entire range are in approximately equal amounts,…

Q: civil engg material

A: Gradation of Aggregate- It is defined as a process that helps in particle size distribution which is…

Q: What is the difference between conducting laboratory tests on the specific gravity and absorption of…

A: Step: 1 Aggregate materials: - It is defined as mixture of coarse and fine particles like concrete,…

Q: make up a computation

A: The computation table for specific gravity and absorption of coarse and fine aggregated have to be…

Q: Design a concrete mix to implement a concrete slab (exposed to sever conditions moisture and…

A: Given, f'c = 30 MPa S = 4 MPa FM = 2.4 Apparent density = 1500 kg/m3

Q: ASTM C127 is the Standard Test Method for Density, Relative Density (Specific Gravity), and…

A: Given data in question ASTM C127 For density, Relative density and absorption capacity To find out…

Q: A Brinell test is performed on a steel using a 1.31 in. diameter indenter with a load of 67275 lbs.…

Q: Why do we need to find the Specific Gravity and Absorption of Fine Aggregate, Surface Moisture of…

A: Introduction:- Engineers value specific gravity because it assists them in establishing the…

Q: In an aggregate mix, the proportions of coarse aggregate, fine aggregate and mineral filler are 55%,…

Q: It is given that an aggregate mix has 260 grams of coarse aggregates and 240 grams of fine…

A: Given-260 gm of coarse aggregates, G=2.6240 gm of fine aggregates, G=2.4Bulk specific gravity of…

Q: Establish the differences between the wear test performed on aggregates smaller than 3/4 "and the…

A: Wear test or abrasion test is carried out to test the hardness property of aggregates. The most…

Q: Q-If aggregates completely pass through a sieve of size 75 mm and are retained on a sieve of size 60…

A: given- Given aggregate completely passes through 75 mm size sieve & retained on 60 mm size…

Q: What are the purposes of doing the specific gravity and absorption of coase aggregates? why?

A: Specific gravity- This test is performed to measure the strength or quality of the material and…

Q: Laboratory specific gravity and absorption tests are run on two coarse aggre-gate sizes, which have…

A: Given: Aggregate A: Bulk specific gravity = 2.814 Absorption = 0.4, Aggregate B: Bulk specific…

Q: In designing concrete structures, normally maximum aggregate sizes are adopted with ranges from 10mm…

A: Greater the size of aggregate lesser is the surface area. Lesser is the surface area indicate that…

Q: Choose one of the two potential aggregate problems below and discuss how it is a problem: a.…

A: The potential aggregate problem: Aggregates are added to concrete to reduce the heat of hydration…

Q: The bulk unit weight of the dry-rodded aggregate inside a rigid container is 25 kN/m3. 35 percent of…

Q: which type of bituminous materials used in the selected zone (colored in green ) shown in figure…

A: - Asphalt (type of Bituminous Materials) used in the selected green zone bcz of in the pavement of…

Q: 1000 g coarse aggregate sample taken from the site showed the following properties in the…

A: Bulk Dry specific gravity is given by ;Bulk Dry specific gravity = Bulk Dry specific gravity = Bulk…

Q: 1. A bioengineer reports that the Young's modulus of articular cartilage is 0.45 MPa and its…

A: Young's modulus (E) = 0.45 MPaPoison ratio = 0.46Find aggregate module of the cartilage (k)?

Q: It is given that an aggregate mix has 260 grams of coarse aggregates and 240 grams of fine…

Q: The percentage of aggregates of fine-ness modulus 2.7 is to be mixed with coarse aggregate of…

A: Given data: The percentage of aggregates of fine-ness modulus (FM) = 2.7 be x It is to be mixed with…

Q: High Soundness value for the aggregate testing provide better resistance can to disintegration. True…

A: True.

Q: : What is meant by: 1. absorption, 2. Moisture content (MC), 3. Bulk density of aggregate,

A: 1. Adsorption- It is surface phenomena, It is the adhesion of atoms, molecules or ions from a…

Q: 90% aggregate temperature is 110°C. On the other hand, bitumen comes in, the room is 10%. Two raw…

A: Given data: 90% aggregate temperature: 110oC 10% bitumen temperature of the mixture is 140oC

Q: In an aggregate mix, the proportions of coarse aggregate, fine aggregate and mineral filter are 55%,…

A: Given that :- In an aggregate mix, Proportions of coarse aggregate = W1% = 55% Proportions of fine…

Q: Prepare report about one of the following topics about aggregate:

A: Soundness of Aggregate: The soundness (AASHTO T104) refers to the durability of an aggregate in…

Q: The "slump" test is E. For room temperature and axial loading, aluminum behaves as a brittle…

A: ANSWERS 1. False because slump test is done to find the workability of the concrete.

Q: Sand bulking occurred due to the addition of water lower than the surface saturated dry condition of…

A: To be discussed Sand property

Q: Design a concrete mix to implement a concrete slab (exposed to sever conditions moisture and…

A: Given, f'c = 30 MPa S = 4 MPa FM = 2.4

Q: Workability should be obtained by the use of a well-graded aggregate which has -----possible. *

A: For concrete to be good workable the aggregate should not be flaky it should be round And the same…

Q: What makes sampling as the most important step in assuring the quality of the aggregates?

Q: This refers to a change from liquid state to solid state of cement paste

A: Setting is the process in which cement concretee starts solidifying and gaining strength. Curing is…

Q: The wet mass of an aggregate sample is 583g and its dry mass is 575g. The test shows the absorption…

A: Finding out the type of moisture condition.

Q: what is the requirement volume of fine aggregates (s.g. = 2..4) if the mass nedded for the concrete…

Q: Sieve analysis for fine and coarse aggregate is done, how can we say that those samples are good and…

A: The fineness modulus is the total of the cumulative percentage that stayed on the each sieve from…

Q: What is the most widely used aggregate type in Turkey. Classify it according to : - source, -…

A: Due to the geological structure of the region, limestone is a very common natural aggregate in…

Q: 20 - Which of the following does not occur if the material under 63 micron exceeds 4% in the…

A: Workability decreases as fine particles increases

Q: Determine the x-bar centroid of the composite figure shown. Where: x=5 ft 2 ft 1ft 2 ft X 1 ft

Q: The desired characteristic strength of a mix is 20N/mm². The standard deviation is 4 N/mm² for 150…

A: Characteristic strength: Characteristic strength of a concrete mix can be defined as the strength…

Concept explainers

Pricing Concrete Work

The concrete work in a project usually holds a high-end cost in terms of cost and value of the work. It becomes an important step in calculating the cost associated with concrete while preparing the project scale. The cost of making concrete depends on the cost of building materials, mixed materials, labor, and machinery. A concrete contractor builds structures from concrete, usually managing all the steps of the process from assembling ingredients to building a holding structure and preparing the mixture. This person or team oversees the delivery and unloading of goods to ensure that they are done properly. Nowadays, most of the concrete in the United States comes from manufacturers working abroad, usually with branches and plants within the provinces. Contributions can range from pre-mixed concrete to basic ingredients, the consumer company then mixes it. Many American-based concrete companies, however, offer concrete products, such as ballads, bricks, countertop, concrete pipe, and building products, as well as concrete construction and installation materials. This article covers both types of suppliers for this set of building materials.

Question

Analysis of Fine Aggregates
Fill in the table:

SIEVE NO
AMOUNT RETAINED (g)
4
33
8
42
10
14
30
164
40
73
100
159
200
20
PAN
31

CUMULATIVE
CUMULATIVE
SIEVE
AMOUNT
AMOUNT
PERCENT RETAINED,
PERCENT PASSING
SIZE
RETAINED, g (a)
RETAINED,g (b)
(c)=(b)*100/TOTAL
(d)=100 - ( c )
TOTAL

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Design a Mix for the following Data. Specified strength = (99.5) MPa, Required Slump = 80 mmMaximum size of aggregate = 25 mm, FM of fine aggregate = 2.40Grading of aggregate as satisfied by ASTM C33 (American Society for Testing and Materials)SSD specific gravity of fine and coarse aggregate = 2.75Rodded bulk density of coarse aggregate = 1600 kg/cubic mAbsorption Capacity of coarse aggregate = 0.9 %Absorption Capacity of fine aggregate = 0.5 %Moisture Content of fine and coarse aggregate = 2 %Exposure Conditions = Normal
It is given that an aggregate mix has 260 grams of coarse aggregates and 240 grams of fine aggregates. The specific gravities of the coarse and fine aggregates are 2.6 and 2.4, respectively. The bulk specific gravity of the mix is 2. The percentage air voids in the mix is (round off to the nearest integer) 2 ×
31
please provide step by step solutions and draw the lever on the graph as well. i know the answers. (c) About 1250 C (d) Fe3C, cementite (e) About 0.7 wt% C, about 72% (f) About 40%, no. (h) Draw the microstructure of a 1.5 wt.% C material that has been heated to 1200 C and then slowly cooled to 600 C. Clearly label all phases.
2 Compare the advantages and disadvantages of fine and coarse aggregates.
The strength of cement is determined by a number of factors.
33
Q2 a civil engineering materials
If I have a coarse aggregate that is low fine modulus range of coarse aggregate, what will happen to the mix and what will happen to the structure as time passes?
Given: w0=2140g, w1=2350g, w2=1105g. What is the absorption of the given coarse aggregate?
Harmful substance in aggregate caused steel bars deterioration is O Clay O gypsum O lead salts reaction O Other: