Help i'll rate! Determine the range of P for which the system of two blocks willbe in equilibrium. Friction is negligible except for the surfaceunder block B.30°120 NPB80 NHj = 0.2-Tip: Draw the Free Body DiagramChoicesDetermine force P I Select]93.5, 11.15, 32.48, 29.28Determine N-force at gound to block B| Select ]300, 400, 100, 200Detemine N-force between surfaces of A and B [ Select]156.38, 13 8.56, 142.12, 200Determine the N-force between the wall and block A I Select 129.68, 69.28, 89.26, 62.89>

Answered: Image /qna-images/answer/f4859b83-3b90-47ce-8784-bd177f687961.jpg

Tip: Draw the Free Body Diagram Choices Determine force P I Select 1 93.5, 11.15, 3 2.48 , 29.28 Determine N-force at gound to block B | Select ] 300, 400, 100, 200 Detemine N-force between surfaces of A and B ( Select ] 156.3 8, 13 8.56, 142.12, 200 Determine the N-force between the wall and block A [ Select ] 29.68, 69.28, 89.26, 62.8 9

Tip: Draw the Free Body Diagram Choices Determine force P I Select 1 93.5, 11.15, 3 2.48 , 29.28 Determine N-force at gound to block B | Select ] 300, 400, 100, 200 Detemine N-force between surfaces of A and B ( Select ] 156.3 8, 13 8.56, 142.12, 200 Determine the N-force between the wall and block A [ Select ] 29.68, 69.28, 89.26, 62.8 9

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. What are the main causes of vibrations in machines?
2 1.54 Explain how you would go about estimating the C and n values for the four tool materials shown in Fig. 21.17.
forming proceɛɛ. 17) Tension is the only type of stress applied in 18) rolling mill type are associated with relatively small diameter rolls in contact with the work piece. 19) Straining a sheet of metal around a straight axis is called 20) The extra portion which must be separated from the extrudate by cutting it just beyond the die exit is called 21) In sheet metal forming the area to volume ratio is considered to be mm. 22) In rolling, if the maximum dratt is 12 mm, & the coefficient of friction is 0.2, thus the minimum roll diameter is 23) The starting work piece in steel hot rolling of plate and sheet stock is called a 24) are 3 methods that can be used to control the metal flow under the blank holder in deep drawing process.
Q2) Choose the correct answer for only 15 (fifteen) of the following. is about 67% of the total forces. A) Longitudinal force. 1) In turning operation, the force. E) thrust force. B) Radial C) feed force. D) cutting force. (C) 2) Which one of the following materials has the lowest hardness: (a) aluminum oxide, (b) cubic boron nitride, f) none of the previous answers. high-speed steel, (d) titanium carbide, or (e) tungsten carbide Which one of the following operations is generally capable of the closest tolerances: (a) broaching. (b) drilling, (c) end milling, (d) planning, or (e) shaping. F) none of the previous answers. 3)
I need answer within 20 minutes please please with my best wishes
Which one of the options isn't classified as a chip form type? a)Non-segmental chip b)Sheared chip c)Discontinuous chip d)Continuous chip