THydropower Plant System The following nametag is specification of a generator in a hydropower plant. MITSUBISHI AC GENERATOR Output Voltage 4. 84.5 MVA 11 kV Current Frequency Speed Power Factor 4435 A 50 Hz 600 RPM 0.86 | Calculate the generated peak voltage. | Calculate real power of the following generator. How many pair-of-poles installed in the generator? Why does not the generator consist of one pair-of-poles only? а. b. C. d.

THydropower Plant System The following nametag is specification of a generator in a hydropower plant. MITSUBISHI AC GENERATOR Output Voltage 4. 84.5 MVA 11 kV Current Frequency Speed Power Factor 4435 A 50 Hz 600 RPM 0.86 | Calculate the generated peak voltage. | Calculate real power of the following generator. How many pair-of-poles installed in the generator? Why does not the generator consist of one pair-of-poles only? а. b. C. d.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Answer number 1, ASAP. With clear solutions and Given.
Four similar synchronous generators are sharing equally the feed to a load of 1 pu referred to the base value of the the synchronous generator, hence,. a) The per unit output of each generator is 0.25 b) The power factor of each generator is 0.25 c) The available info is insufficient to calculate the per unit impedance of the load d) None of these
Question A short shunt compound generator delivers a load current of 39A at 240V, and has the armature, series field and shunt field resistances of 0.450, 0.060 and 2200 respectively. Calculate the generated voltage.
Problem-7 (e)- A 4 pole, 50 Hz synchronous generator has 48 slots in which a double layer winding is housed. Each coil has 10 turns and is short pitched by an angle to 36° electrical. The fundamental flux per pole is 0.025 Wb. Find the line-to-line in induced emf (in volts), for a three wire connection.
A 480V, 50HZ, star-connected 6 poles synchronous generator has a per phase synchronous reactance of 0.30. Its full load armature current is 60A at 0.85 lagging power factor. This generator has friction and windage losses of 1.5kW, and core losses of 1kW at full load. Assume copper losses are negligible due to negligible armature resistance. Determine the: i) rotational speed of the generator, ii) generated emf voltage of the generator, ii) efficiency of the generator, and iv) voltage regulation.
When this generator is connected to a 13.8 kV distribution feeder of negligible impedanceand operates at an output power of 8.75 MW at 0.9 power factor lagging, work out the field current, the reactive-power output, and the load angle for this operating condition.
A synchronous generator supplies rated power at 0.8 pf lagging.ra = 0.015p. u., andxl 1p.u. . Find out the possible terminal voltage. In case of the practical operation, which terminal voltage is more feasible? =
H.W Q1) A four pole, three-phase synchronous generator is rated 250 MVA, its terminal voltage is 24 kV, the synchronous reactance is: 125%. ERI • Calculate the synchronous reactance in ohm. Calculate the rated current and the line to ground terminal voltage. Draw the equivalent circuit. • Calculate the induced voltage, E., at rated load and pf = 0.8 lag.
A synchronous generator is connected to an infinite bus with excitation voltage Ef = 1.3 pu. The generator has a synchronous reactance of 1.1 pu and is delivering real power (P) of 0.6 pu to the bus. Assume the infinite bus voltage to be 1.0 pu. Neglect stator resistance. The reactive power (Q) in pu supplied by the generator to the bus under this condition is
A 3 phase, star-connected, cylindrical rotor, 10 MVA, 11kV synchronous generator is supplying rated power to a unity power factor load. The terminal voltage and real power input to the machine are kept constant. A purcly inductive load is now switched in parallel to the unity power factor load, so that the load draws power at 0.85 power factor lagging. What is the percentage incrcase in the ficld excitation current under the new operating condition, if the synchronous reactance of the machine is 5N/ phase? Assume lincar flux- current relationship for the field.
Terminal voltage of shunt G1 generator in idle operation is 500 V. The terminal voltage of the G1 generator drops to 470 V if it delivers a load current of 600 A. The idle operating voltage of the shunt G2 generator is 505 V. G2 generator terminal voltage drops to 470 V in case of 400 A load current. These two generators are connected in parallel to feed a load of 400 kW. Voltage-power characteristics of generators are linear. According to this; a. Draw the connection diagram given in the question. b. Obtain the network voltage and the powers of the generators. c. Calculate the current given by each generator to the load.