Three forces and a moment are applied to the beam shown in Figure 1(b). Replace the loading acting on the beam by a single resultant force (in Newtons) and specify where the resultant force acts, measured from A. Take P1 = 448 N, P2 = 736 N, c = 1.28 m and d = 4 m. P, P2 30 300 N B d -3 m- 1500 N m

Three forces and a moment are applied to the beam shown in Figure 1(b). Replace the loading acting on the beam by a single resultant force (in Newtons) and specify where the resultant force acts, measured from A. Take P1 = 448 N, P2 = 736 N, c = 1.28 m and d = 4 m. P, P2 30 300 N B d -3 m- 1500 N m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine the magnitude of the resultant force (in N) of the coplanar force system shown in the figure below where the horizontal force P = 109 N and the couple M = 684 Nm. M N m A 150 N 300 mm 250 mm P N 400 mm 90 N
Question 2) Forces of F1=7 kN in the +y direction and F2=13 kN in the -z direction are acting on the arm from point B in the figure. From the point C, a moment of magnitude M=4 kN.m acts in the +y direction. The lengths of the arm are also given as L1=0.8 m and L2=0.6 m. The radius r in the a-a section taken over the arm is r=0.023 m and it is desired to determine the stress state at point A. The shear modulus of the sleeve material is G=78 Gpa. According to this;Question 2-A) Find the shear stress at point A due to the shear force. (Write your result in MPa.)Question 2-B) Find the shear stress due to the torsional moment at point A. (Write your result in MPa.)Question 2-C) Find the normal stress caused by the normal force at point A. (Write your result in MPa.)
92: The screw eye in figure below subjected to two forces F, and F,. Determine the magnitude and diredion f the resultant force using the Cosine law . Law• F=150 N Fi 100 N 15 "
For the loading system shown below, replace the loading by a single force and a moment at D What is the vallue of the moment? No decimal digits are needed Take F1 81 N, F2= 191 N, F3 = 243 N, and MC = 191 Nm F2 1m 2 m 3 m B 2 m Mc 60 3m F1
Problem 3 w2 kN/m 7x kN/m From the figure, w1=9kN/m, w2=13KN/m 1. Find the resultant of the forces 2. Find the location of the resultant from point B. w1 kN/m 5m Sm 5m
Replace the loading by an equivalent resultant force and couple moment acting at point O. (Figure 1) The loading function is w = 4.5x² lb/ft. Figure W 10 ft -X ▼ Part A Determine the magnitude of the equivalent resultant force. Express your answer in pounds to three significant figures. FR = Submit Part B X = 路 VG ΑΣΦ Submit Request Answer vec Specify the location of the equivalent resultant force on the beam, measured from the left end. Express your answer in feet to three significant figures. VE ΑΣΦ Request Answer ? Pearson ? vec lb ? ft
Consider (Eigure 1). Figure F₁-375 lb 8 ft- + 6 ft F = 500 lb -5 ft- 0.5 ft F₂= 160 lb Part A Determine the moment about point B of each of the three forces acting on the beam. Express your answers in poind-feer to three significant figures and separated by commas. (ME) B: (Mr.) B. (M₁) ₁ = Submit Previous Answers Request Answer X Incorrect; Try Again AZ vec Provide Feedback A ? lb ft
Find the magnitude and direction of the resultant force for the system of forces shown in the figure. Where F, -30 N, F2 =5N, F3 =30 N, F4 30N, Fs = 30N & F6 - 70N. The angles e, =15, e; =35, 04 = 20°, e, = 25• (Enter only the values in the boxes by referring the units given in bracket) F2 F6 Fs (1) The horizontal component EH of the given system is (unit is in N) (2) The vertical component EV of the given system is (unit is in N) = (3) The resultant of the given force system is (unit in N) = (4) The direction of Resultant is (in") =
Find the tension in the diagonal cable and the magnitude and direction of the force on the strut by the pivot. The weight of the crate is 2500 N. The strut is uniform and 3.0 m and its weight is 6000N. The angles are a=40 and ß=50 degrees. Draw all the forces acting in the system. Use 2 significant figures in your answer. Write units in calculations. B la
Find the magnitude and direction of the resultant force for the system of forces shown in the figure. Where F1 =10 N, F2 =15N, F3 =10 N, F4 =55N, F5 = 70N & F6 =70N. The angles ϴ2 =20ᵒ, ϴ3 =35ᵒ , ϴ4 = 40ᵒ, ϴ6 = 45 ᵒ (1) The horizontal component of the given system (unit is in N) = (2) The Vertical component of the given system (unit is in N) = (3) The resultant of the given force system is (unit in N) = (4) The direction of Resultant is (degrees) =
The force F = {-6i + 3j + 18 k} N is applied to the block shown in (Figure 1). Figure X -3 m D B 1.5 m G 3m F 1 of 1 > Part A Determine the moment of the force F about the diagonal AF of the rectangular block. Express your answers in newton-meters to three significant figure. Enter the x, y, and z components of the moment separated by commas. (MAF)z. (MAF)y, (MAF) z = Submit VE ΑΣΦ Provide Feedback Previous Answers Request Answer ↓↑ vec X Incorrect; Try Again; One attempt remaining ? N.m Next >
Find the magnitude and direction of the resultant force for the system of forces shown in the figure. Where F1 =15 N, F2 =35N, F3 =20 N, F4 =35N, F5 = 30N & F6 =10N. The angles ϴ2 =15ᵒ, ϴ3 =35ᵒ , ϴ4 = 20ᵒ, ϴ6 = 20 ᵒ ) The horizontal component of the given system (unit is in N) = __________ Answer for part 1 (2) The horizontal component of the given system (unit is in N) = __________ Answer for part 2 (3) The resultant of the given force system is (unit in N) = Answer for part 3 (4) The direction of Resultant is =