A folding tray mechanism is attached to a wall as shown. Find the internal forces and bending momentin the lower support arm at section s-s, located midway between points B and E, when a force of F =185 N is applied at an angle of 0 = 15°.EhiDbValues for dimensions on the figure are given in the following table. Note the figure may not be toscale.Variable Valuea15 cm23 cm32 cmhị21 cmh217 cmThe internal axial load at section s-s is A =-80.6N.The internal shear load at section s-s is V = 80.3N.The internal bending moment at section s-s is M = 10012N-m.

A folding tray mechanism is attached to a wall as shown. Find the internal forces and bending moment in the lower support arm at section s-5, located midway between points Band E, when a force of F = 185 N is applied at an angle of 0 = 15°.

A folding tray mechanism is attached to a wall as shown. Find the internal forces and bending moment in the lower support arm at section s-5, located midway between points Band E, when a force of F = 185 N is applied at an angle of 0 = 15°.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Draw the front, Side and top
A force F = 1757 N acts upon a piston head, as shown in the figure. The gudgeon pin G connects the connecting rod to pin C where it connects to the crankshaft at S in a large military vehicle. Find the moment of the force at S.
Find the internal forces and moment acting at point B in the beam that weighs 15 kN. The cable tension is 6 kN. Clearly show your FBD and equations used. B 30° -0.3 m+ W=15 kN 0.6 m 0.6 m-
a beam is supported by a pin support at A and a roller support at B. For this question, leave your answer in terms of the variables w and L. (a) Using equilibrium of the full beam, find the support forces at A and B. (b) First section: Make an arbitrary cut between points A and B. Take the distance of the cut to be x along the beam from point A. Draw the free-body diagram for the left section and find functions for the internal shear force, V(x), and bending moment, M(x), in the section of the beam between A and B. (c) Second section: Repeat part (b) for the section of the beam between B and C. Take x to still be the distance from point A. (f) Find the value of x at which V(x) = 0. The internal bending moment reaches a maximum at the same point as V(x) = 0. Find the maximum bending mo- ment. pin Sketch the shear and bending moment diagrams. B L W C roller
1 ft 3 ft B 3 ft 3 ft (-9002 + 800f + 1000k) Ib.ft 6 ft 3 ft E (-300î – 400ĵ + 100k) Ibs The applied force at point E and the applied couple moment at point D are shown in the figure. Complete/calculate the following: (Where applicable, express the results as the (x, y, z) components of a Cartesian vector) 1. Draw the free-body diagram (FBD), showing the appropriate reaction forces and/or moments at the supports. (You must show the reactions in their component form i.e. show RAx, MRAX etc. on the FBD). Note: The support at point A is not able to resist a moment about the 'X' axis but is able to resist a force in this direction. 2. ME, which is the moment vector at point A due to the force acting at point E 3. Me, which is the moment vector at point A due to the tension force acting at point B. Write the vector in terms of the unknown tension magnitude 'T' 4. Set up the equations of equilibrium (You must show all relevant equilibrium equations one below the other. 5. Calculate the…
Answer should be : Mo : 189.3 lb ft, O = 18.5 lb at 248 from positive axes
Find the internal forces and moment acting at point D in the beam (treated as 2-D and no thickness of beam). The tension in cable CB is 100 Ib. show FBD 6 ft 300 ft-lb 200 lb 3 ft-+3 ft e 3 ft 6 ft-
F A C D B TI F KSA
please help me solve and explain
A Pin spanner as shown in Figure, requires moment of 80 Nm to turn the 200 mm diameter shaft about its center O under the action of the applied force P. determine the contact reaction force on the smooth surface at the point A. Engagement of the pin at B may be considered to occur at the periphery of the collar OPTIONS:(MULTI CORRECT(MAY BE)): 1.Reaction at Point A is around 1047 N 2.Value of force P is around 102 N 3.Value of force P is around 133 N 4.Reaction at Point A is around 720 N 5.Reaction at Point A is around 1321 N 6.Value of force P is around 200 N 7.Value of force P is around 213 N 8.Reaction at Point A is around 970 N