Three dimensional F1 = 48i + 73j - 14k F2 = 73i - 11j + 131k   for vectors F2 - F1 =?

Q: A) Write the commands to draw shape (A) by using AutoCAD program. B) Write the Modified commands…

A: AUTOCAD is the application software used for drawing and drafting plans, designs and basic shapes,…

Q: Determine the true length of lines SD and PF. Then draw the point view of line SD. Use only two…

A:

Q: Problem #4 G F B X KN 3+B m Determine the following: 18. Horizontal reaction at G. (kN) 19. Bar…

A: Given data x = 137 y = 37 a = 6 b = 8 c = 1  T = Tension in member C = compression in member

Q: y(V) – y = 0 1. y" – 10y' + 29y = 0 2. %3D

A:

Q: Civen that the tension in segment AB 130 N WITH a rathio of 1H: 2v, which of the fo llowing nearly…

A:

Q: Determine the XT and YT a. Using the Top Most, Left Most Reference Line b. Using the Bottom Most,…

A:

Q: Polar moment of inertia (I) in cm4 at a rectangular section having width b = 2 cm and depth d = 6 cm…

A: Rectangular section- Width b=2 cm, Depth d = 6 cm, Polar moment of inertia IP=?

Q: There are OA has length I A Find B Chiven: L₁ = cm 42 = (0,85₁-357cm = 14 F₁ 143 F 13 A.B has leugh…

A: Given: F1→=135i+145j-75k kNF2→=60i-85j-75k kNF3→=-115i+65j-55k kNF4→=25i-25j-35k kNL1→=125i+0j+0k…

Q: Problem II. From a triangular steel plate XYZ, a triangular section VwZ was cleanly cut off. What…

A: Given data:

Q: Problem 5: A double-angle tension member, 2L 76 × 51 × 6.4 LLBB (Longer legs are connected back to…

A: Given Gross area =1.2 in2 Dead load =15 kN= 3.372 kips Live load= 6kN=1.3488 kipi

Q: 5 in. 1 8 in. R = 6 in. 2 in.- y H (a)

A:

Q: Determine the X¡ and YT(using both a and b) a. Using the Top Most, Left Most Reference Line b. Using…

A:

Q: Q.77 Laplace transform of e 2t cos (4t) is s- 2 S+2 (a) (b) (s - 2)? + 16 (s- 2)? + 16 S-2 S+2 (c)…

A: given-e-2tcos4t

Q: Derive an expression of the maximum statical moment of area, Q and its location from the given…

A:

Q: Q. No. 01 Find out the missing storm precipitation of station "C" given in the table 1 using station…

A:

Q: 5(y")² + 10(y')³ = 3x -y d²y dt² y"" +3y' +2y=x² 8²v ἂν = +1 ay² ax d²y dx² +(5t + 1)² = 0 DEPENDENT…

A: Whenever we differentiate a variable with respect to another variable, the variable which gets…

Q: The member is loaded with load P as shown. a) Find the stress at points A,B,C and D b) the points…

A: Question is based on the section subjected to the point load. Magnitude of load and dimension of…

Q: Given: ● X ● x1 x1 = 15.35 mm . x2 = 16.74 mm x3 = 16.10 mm y1 = 19.32 mm y2 = 20.55 mm • y3 = 16.37…

A: Section diagram:

Q: Show that the function f(x, y, z) = e3x+4y.cos(5z) satisfy 32f a2f + əx² Əy² 82f = 0 3z² 02f 02f 02f…

A:

Q: F A B D 1m 2 m 2 m Set P (kN) A (1,3,5,7,9) в (2.4,6,8,0) 300 450 Determine the value of F that will…

A: P = 450KN

Q: Diesel fuel with a specific gravity of 0.8, flows through the Venturi meter shown in figure below.…

A: Given data V=V1=38 m/sh1=96cm=0.96mh2=12cm=0.12mD1=6cm=0.06mD2=3cm=0.03mθ=20oSpecific gravity=0.8

Q: Q. No. 04 Compute the discharge in the stream based on the current meter measurements provided below…

A: Calculating the Velocity at 0.6 ft the depth using the formula: V0.6 ft=V0.2 ft-V0.8 ft2

Q: x2 xedy + () +1 dx ||

A:

Q: t3 – 3t? + 5t – 8 5 sinh 3t + 4 cosh 3t

A:

Q: Y. 3.5 314 1. The cross section shown in the figure is a structural member known as a z-…

A:

Q: 4. Determine whether u and v are orthogonal, parallel, or neither. u = -5i + 24j - k v = 5i +j-k…

A:

Q: Find Ix for the shape below: 2.0 2.0 Ix: Componen Ai 1.0 |ΣΑΙ = |Yave = ΣAiyi/ΣΑΙΞ dy = Yave - yi =…

A:

Q: What is the degree of the homogeneity of the function f(x,y)= Vx³ – 5x²y – y³?

A: Answer :  option (b) 3/2 is correct.

Analysis and Procedures for Material Selection

The term material selection means to select the right material for various engineering applications. There are various engineering materials available and each has different individual properties. Thorough knowledge of the material properties and behavior is crucial in the design process. For instance, a structural member, such as a beam, is used to support vertical shear loads by the building itself. To withstand such loads, the material of the beam must possess adequate strength and stiffness to resist any deformation that might lead to the formation of cracks.