This problem illustrates that the factor of safety for a machine element depends on the particular point selected for analysis. Here you are to compute factors of safety, based upon the distortion-energy theory, for stress elements at A and B of the member shown in the figure. This bar is made of AISI 1006 cold-drawn steel and is loaded by the forces F= 0.55 kN, P= 4 kN, and T= 25 N.m. Given: Sy= 280 MPa.

This problem illustrates that the factor of safety for a machine element depends on the particular point selected for analysis. Here you are to compute factors of safety, based upon the distortion-energy theory, for stress elements at A and B of the member shown in the figure. This bar is made of AISI 1006 cold-drawn steel and is loaded by the forces F= 0.55 kN, P= 4 kN, and T= 25 N.m. Given: Sy= 280 MPa.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The stepped and surface-ground steel bar in the figure is subjected to a bending moment varying between Mz=100 Nm and Mz=250 Nm and a torsional moment varying between Tx=80 Nm and Tx=320 Nm in opposite directions. The tensile strength of the rod material is Sut=800 MPa and it works under room conditions. For 50 percent reliability, check the fatigue safety of the rod.
can you solve (a) and (c) using mohrs circle
The shaft shown the figure below, is supported by a bearing on the left end. The shaft also supports a pulley on the right end, which rotates. The tensions in the belt of the pulley are F. =2,739 y and F,=1,362 N. Also, a completely reversed axial load of F 11 N is applied to the right end. The shaft is made of UNS G10450 CD steel, with 2. a ground surface and 99 z reliability and operates at room temperature. Assume, K =1.35 for torque and formula 6- 34 to calculate K fs' K, - 1 K = 1 + (6-34) 1+ va/ Vr Bending or axial: Va = 0.246 – 3.08(10)S+ 1.51(10-)S, – 2.67(10-*)S 50 s Su s 250 kpsi Va = 1.24 - 2.25(10-)S+1.60(10)$ – 4.11(10-1)S, 340 S S 1700 MPa (6-35) Torsion: Va = 0.190 – 2.51(10-)S+ 1.35(10-), – 2.67(10-)S 50 < Su < 220 kpsi Va = 0.958 – 1.83(10-)S+ 1.43(10-")S-4.11(10-1)s 340 < S S 1500 MPa (6-36) All fillet radius r-0.1d All dimensions are in mm 300D -30 100 :600 1. Identify the critical point(s) on the shaft and show it clearly on the diagram. 2. Draw the cartesian…
DRAW THE FBD FOR THIS PROBLEM. PLEASE PROVIDE DETAILED SOLUTION FOR THIS PROBLEM
A solid round bar with diameter of 2 in has a groove cut to a diameter of 1.8 in, with a radius of 0.1 in. The bar is not rotating. The bar is loaded with a repeated bending load that causes the bending moment at the groove to fluctuate between 0 and 25 000 lbf in. The bar is hot-rolled AISI 1095, but the groove has been machined. Determine the factor of safety for fatigue based on infinite life and the factor of safety for yielding. Plars & .
Please help with the stress, mohir circle, etc. Thank you
What is the difference between static and dynamic loading.. Explain with the drawing the types of dynamic loading. b) In the figure shown, a column of AIAL 1045, cold drawn, rotates on bearings. A force of SKN is applied to it8kn . Find the modified resilience limit stress, the stress of Al-Tin Amra
Don't copy from any source and don't give handwritten solution
A thin-walled column has a circular cross section of diameter 200 mm and thickness 5 mm. It carries an axial load Pand a torque of 20 kNm. If the material of the column fails in simple tension at a stress of 240 N/mm² find the maximum allowable value of Pusing the Tresca and von Mises theories of elastic failure. Ans. 640 kN (Tresca), 670.6 kN (von Mises).
Requlred Informatlon A rotating shaft of 25-mm dlameter Is simply supported by bearing reaction forces R;and R2. The shaft is loaded with a transverse load of 13 kN as shown In the figure. The shaft is made from AISI 1045 hot-rolled steel. The surface has been machined. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 200 mm 25 mm 13 kN -50 mm Not to acale Determine the minimum fatigue factor of safety based on achleving Infinite life. The minimum fatigue factor of safety is
1. A cold drawn mild steel, AISI 1018CD is used to fabricate the hollow shaft as shown in Figure Q1. Torque of 15 Nm and 30 Nm are exerted at B and C, respectively. The outer diameter of the shaft is D = 20 mm and the inner diameter is d = 15 mm. If the modulus of rigidity for the steel used is given as G = 78 GPa, determine: a) the maximum and minimum shear stresses at sections a-a and b-b. b) the angle of twist at end C. 0.3 m A a; B 15 Nm 0.8 m b. b: Figure Q1 с D 30 Nm
Answer is closer to 32 kN/m, but how does it get there?