This problem illustrate that the factor of safety for a machine element depends on the particular point selected for analysis. Compute factors of safety, based upon the distortion energy theory, for stress elements A and B of the member shown in the figure. This bar is made of AISI 1015 Cold-Drawn Steel and is loaded by the forces F= 500 N, P = 5000 N, and T= 25 Nm.

This problem illustrate that the factor of safety for a machine element depends on the particular point selected for analysis. Compute factors of safety, based upon the distortion energy theory, for stress elements A and B of the member shown in the figure. This bar is made of AISI 1015 Cold-Drawn Steel and is loaded by the forces F= 500 N, P = 5000 N, and T= 25 Nm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Required Information For a bar of AISI 1015 cold-drawn steel, determine the factor of safety using the distortion-energy and maximum-shear- stress theories for the following principal stresses. A = 28 kpsl, and og = 15.5 kpsi The factor of safety from the maximum-shear-stress theory is 1.94 1.88 and the factor of safety from distortion-energy theory is
If d=40 mm, L=796 mm, F=29 kN, T=1.7 kNm and fail stress=156 MPa, calculate the apparent factor of safety for this loading condition. Give your answer to 2 decimal places.
Required information This problem illustrates that the factor of safety for a machine element depends on the particular point selected for analysis. Here you are to compute factors of safety, based upon the distortion-energy theory, for stress elements at A and B of the member shown in the figure. This bar is made of AISI 1006 cold-drawn steel and is loaded by the forces F= 0.55 kN, P= 4 kN, and T=25 N-m. Given: Sy= 280 MPa. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. B 15-mm D. -100 mm What is the value of the axial stress at point A? The value of the axial stress at point A is MPa.
In the figure above, the shaft has a diameter of 50mm, and the diameter of pulleys C and D are given tobe 600 mm and 400 mm, respectively. ?1 = 1000 N, ?2 = 500 N and ?3 = 1500 N. But in addition tothe force on the pulleys, a compressive axial force of 100 kN is acting on both ends of the shaft. Theshaft is made from a brittle material with an ultimate tensile strength ??? that is half of its ultimatecompressive strength ???. The desired factor of safety is ? = 2 for the shaft.e. Determine the principal stresses corresponding to maximum bending and torsional shear stresses.Ignore transverse shear stresses due to bending.f. Use Maximum Normal Stress Theory and find the minimum required ??? and ???.g. Use Brittle Coulomb-Mohr Theory and find the minimum required ??? and ???.h. Use Modified Mohr Theory and find the minimum required ??? and ???.i. Use graphical method to check your answers in parts (a), (b) and (c).
please i want a clear solution
I need handwritten and correct only otherwise skip
EXERCISE 4 BY NC ND T 45 kN.m 200mm dAB = 20mm Figure shows a composite rod structure subjected to torsional loadings. AB and DE are solid rod made from Tg= 15 kN.m dBc = 40mm aluminium (Ga 27 GPa). Rod BD is made from brass alloy 150 mm (G= 39 GPa) consists of two portions (solid portion BC and br 150 mm hollow portion for CD) with inner and outer diameter of 35 mm and 40 mm respectively. Determine; Tp= 30 kN.m i) Absolute maximum shear stress in AB Ans (TAB)max 28.64 GPa 400 mm ii) Absolute maximum shear stress in BC dDE = 55mm Ans (TBC)max 2.39 GPa iii) Absolute maximum shear stress in CD Ans (TCD)max 5.77 GPa iv) Absolute maximum shear stress in DE Ans (TpE)max= 1.84 GPa
A round steel rod made of structural steel, AISI C1118, As rolled is to be used as a column, centrally loaded with 15 kips; N= 2.75. Determine the diameter for (a) L= 20 in. (b) L= 5 in. (c) the same as (a) and (b) except that the material is AISI 9850, OQT 1100 F. Is there any advantage in using this material rather than structural steel?
For same problem setup in Q1 except for the length, if the yield strength is 145 MPa, calculate the critical length under which the column would fail by yield and over which the column would fail by buckling.
Compute factors of safety, based upon the distortional energy theory, for stress elements at A and B of the bar shown. The bar is made of AISI 1006 cold-drawn steel and is loaded by the forces F = 0.55 kN, P = 4.0 kN, and T = 25 N-m. 15-mm D. -100 mm
QUESTION 3: Square profile made of hollow 1045 steel, with a length of 6 meters with a cross-sectional area of 40x40 mm and a wall thickness of 4 mm, is subjected to an axial tensile load of "6" KN from both ends. remains. (E1045 = 207 GPa, Yield 1045 = 414 MPa) Calculate %3D %3D the final length of the rod under this tensile load in "mm".
shows a round bar subjected to a bending load F = 0.80 kN, and axial tension P = 7.2 kN, and a torsional load T = 40N.m. The round bar is made of steel with S, = Syc = 490 MPa. Compute the stress components and the magnitude of %3D principle stresses that act at A. Determine the factor of safety using Distortion Energy Theory 100mm F Ø20mm P T