this is the answer I need solutionsa) no stirrup neededb) s = 275 mmc) s = 275 mmd) s = 90 mme) s = 65 mmf) increase beam size A rectangular beam has the following properties:Stirrup diameter = 10 mmfyt = 276 MPabw = 300 mmd = 550 mmf'c = 21 MPaDetermine the required spacing vertical U-stirup when therequired shear strength Vu is (a) 25 KN, (b) 90 KN, (c) 130 KN,(d) 290 KN, (e) 360 KN, and (f) 570 KN.

bw=300 mmd=550 mmf'c=21 MPaStirups diameter=10 mmfyt=276 MPa To find:- Spacing of vertical stirrups…

A rectangular beam has the following properties: bw = 300 mm Stirrup diameter fyt = 276 MPa d = 550 mm f'c = 21 MPa = 10 mm Determine the required spacing vertical U-stirup when the required shear strength Vu is (a) 25 KN, (b) 90 KN, (c) 130 KN, (d) 290 KN, (e) 360 KN, and (f) 570 KN.

A rectangular beam has the following properties: bw = 300 mm Stirrup diameter fyt = 276 MPa d = 550 mm f'c = 21 MPa = 10 mm Determine the required spacing vertical U-stirup when the required shear strength Vu is (a) 25 KN, (b) 90 KN, (c) 130 KN, (d) 290 KN, (e) 360 KN, and (f) 570 KN.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 2.10 A square yellow it is subjected t the allowable t mum allowable cross section if

Q: A simply supported beam shown below is HEA 400 of 5355 steel. It is laterally supported at points…

A: Since the beam is symmetrically loaded we get Maximum Bending Moment at the Midspan.Maximum bending…

Q: 60 b P P 150 100 100 100

Q: What will be the block shear strength of a tension member as shown in figure below? The steel is of…

Q: A steel plate (called cover plate) having cross-sectional dimensions 7.0 in. x 0.49 in. is welded…

Q: CH2-Resultant pof-Adobe Acrobat Pro Estended Fle Edit View Decument Comments Forms Tooks Advanced…

Q: Problem 2: A existing (E) W18x40 is deflecting too much and you were asked to decrease the floor…

A: Given data,section (E)W18x 40space is limiteduse maximum 3" deep memberFindchoose the WT member to…

Q: Example : Replace the three forces acting on the bent beam by a single equivalent force R. Specify…

A: The free-body diagram of the beam: The resultant force R=-F1+F2-F3 As given the forces in vector:…

Q: Column Design: Given: a solid circular column carrying a compressive load of 8500 lb with pinned…

A: Given, SAE 4140 OQT 1000 steel

Q: bolted lap joint

Q: The axial assembly consists of a solid 0.93-in.-diameter aluminum alloy [E = 10400 ksi, v = 0.32, a…

A: Determine: (a) the normal stresses 01, 02 in both rods at 138°F (positive if tensile, negative if…

Q: A column in the upper story of a building is subjected to a compressive load from the following…

A: D = 308 kNL = 170 kNLr = 187 kNW = 197 kN To determine:a) factored loadb) Required design strength…

Q: A rack is made from roll-formed sheet steel and has the cross section shown. Determine the location…

A: Consider the diagram shown below. The length of each segment with respective to their centroid is…

Q: The given angle bar L125x75x12 with Ag = 2,269 sq.mm. is connected to a gusset plate using 20 mm…

Q: For the beam shown below: a) Calculate the elastic curve equation Ely Mo A = R³L 6 Mox³L + cx + C₂…

Q: As shown in the figure below, a C7 x 12.25 tension member of A572 Gr 50 steel is connected to the…

A: Answer We know that allowable strength of a member is given by minimum of the following strength 1)…

Q: 1½" 3"<3"→ -1½" 2" С7x 12.2 O O 2" t = ½"

A: Calculation Gross-section nominal strength; Pn = FyAg=50×(3.6)=180 kips Calculation of Net section…

Q: An A36 tension member shown in the figure is connected with three 19 mm diameter bolts. Dia. Of bolt…

Q: Refer to the beam loading diagram shown If the beam is made from A992 and is continuously braced,…

Q: What is the required diameter of sag rods in mm? Considering sag rods and tie rods at midspan…

Q: 3) For the concrete beams shown, draw the approximate deflection shape and draw the locations of the…

A: To draw: Approximate deflection shape and location of reinforcing bars

Q: A channel is used as a tension member with the web of the channel welded to a 9.5 mm thick gusset…

A: To solve these problems, we'll use the Load and Resistance Factor Design (LRFD) approach. LRFD…

Q: Determine the end moments of the restrained beam shown in Fig. P-714. W. MATHalino .com A L Figure…

Q: TENSION MEMBERS: THE SINGLE 200 X 10 mm STEEL PLATE IS CONNECTED TO A 12 mm THICK STEEL PLATE BY…

A: Note:- Hi! Thank you for the question, As per the honour code, we are allowed to answer three…

Q: Q1. Identify all zero force members B E WW HL100 kN 160 kN

Q: SITUATION 14: A PL 300 x 20 mm is to be connected to two plates of the same material with half the…

Q: Calculate quantity of the Reinforcing for the beam shown in figure below. A 0.3 m 3.2 m 2016 08 @…

Q: 1) Calculate maximum deflection of the beams. 2) Check the suitability of the section assuming the…

A: UKB 457 x 152 x 82 I = 366,000,000 mm4 E = 2 x 105 FIND1- Calculate maximum deflection of the…

Q: m alone)? (Assume bending arour

Q: 300 mm B 600 mm 400 N·m 600 mm 200 N·m 800 N·m The 50-mm-diameter A992 steel shaft is subjected to…

A: given data,change solid steel shaft into the tabular cross sectionFindAngle of twist at AMaximum…

Q: (1) 2/" 3" 4#9 bood 14" (1) Ec = ? (2) fr=? (3) Mer=? #4 fé = 5 ksi Grade 60 Steel NWC. b=14", h=24"…

A: As per Bartleby's guidelines we are supposed to answer only first three questions. Kindly repost…

Q: A steel plate (called a cover plate) having cross-sectional dimensions W2 5.0 in. x 0.4 in. is…

A: The given data is shown below: W2=5 in.×0.4 in.W1=12 in.×87 in.

Q: A channel is used as a tension member with the web of the channel welded to a 9.5 mm thick gusset…

A: To solve these problems, we'll use the Load and Resistance Factor Design (LRFD) approach. LRFD…

Q: Question: Assuming nominal shear reinforcement is provided, calculate the concrete contribution to…

A: Beam width, bw = 400 mmBeam effective depth, d = 675 mmConcrete strength is fc = 30 MPaTo find:The…

Q: 2. For the figure shown, calculate the net area of the 10 x 200 mm plate. The plate is connected at…

A: We are given chain pattern of boltingNet area for chain pattern of bolting is given by An = Ag -…

Q: Determine the tensile development length required a) using ACI Equation, assuming Ktr = 0 b) using…

A: Determine the tensile development length required a) using ACI Equation, assuming Ktr = 0 b) using…

Q: Using the method of composite areas, find the moment of inertia about the centroidal y axis. The…

A: Consider the given diagram and data

Q: 1) Column AB is made of solid 410, cold worked Steel with the following specification Sy=85 KSI,…

A: For checking the type of failure, it is necessary to determine the type of column whether short or…

Q: Determine the design strength of an UNP300 with four lines if 20 mm diameter bolts in standard…

A: Given- diameter of bolts=20mmFu=370MpaFy=240MpaFor UNP 300B=100mtf=16mmAN=0.949m2/m

Q: QUESTION 5 Column Design: Given: a solid circular column carrying a compressive load of 8500 lb with…

A: SAE 4140 OQT 1000 steel

Q: uired information TE: This is a multi-part question. Once an answer i owe scissors roof truss is…

Q: Beam and load cases Maximum Beam Deflection PL³ dmax 3EI

A: To find maximum deflection of cantilever beam

Q: Unit for Reinforcing Bars a. Kilograms b. Tons c. Pieces d. All of the above

A: Generally unit for reinforcing bar are measured in Quintal. 1 Tons= 9.072 Quintal = 907.2 Kilograms

Q: he anchors used in GFRC panels are typically a. two-piece anchors. b. one-piece anchors. c. either…

Q: Determine the slenderness ratio and the Euler buckling load for round wooden dowels that are 2.15 m…

Q: Determine the required development length in the beam and in the column for No. 10 bars shown in the…

A: Concrete strength(fc)=4300 psi,Yield strength of the concrete(fy)=60 ksi,Dead load(DL)=15 k,Live…

Q: If the unfactored shear actions due to dead and live loads are VG = 300 kN and VQ = 80 kN (including…

A: Dead loads, VG = 300 kN Live loads, VQ = 80 kNTo find:The nominal shear stress (vn) acting on the…

Q: 10 kN 12 kN 4 kN 8 kN (1) (2) A 10 kN В C 12 kN D 2.0 m 2.5 m 3.0 m

Question

this is the answer I need solutions

a) no stirrup needed

b) s = 275 mm

c) s = 275 mm

d) s = 90 mm

e) s = 65 mm

f) increase beam size

A rectangular beam has the following properties:
Stirrup diameter = 10 mm
fyt = 276 MPa
bw = 300 mm
d = 550 mm
f'c = 21 MPa
Determine the required spacing vertical U-stirup when the
required shear strength Vu is (a) 25 KN, (b) 90 KN, (c) 130 KN,
(d) 290 KN, (e) 360 KN, and (f) 570 KN.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given

VIEW

Step 2: Shear force resisted by concrete

VIEW

Step 3: Calculation of spacing

VIEW

Step 4: Calculation of spacing

VIEW

Step 5: Calculation of spacing

VIEW

Solution

VIEW

Step by step

Solved in 6 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 800N package is supported by two cables and a rod as shown. 1600mm 600mm 600mm D B 1800mm 1200mm 800mm Which of the following shows the most ideally constructed force diagram of point A? A C C D D z Z B TAC B TAC FDA FDA TAR A TAB A 800 N y 800 N y B C D C D D z B TAC B TAC FDA FDA TAB A 800 N TAB A 800 N y
A steel plate (called a cover plate) having cross-sectional dimensions W2 8.0 in. x 0.7 in. is welded along the full length of the bottom flange of a W, 12.0 in. x 14.0 in. wide-flange beam (see the figure, which shows the beam cross section). I W2 cover plate What is the percent increase in the smaller section modulus (as compared to the wide-flange beam alone)? Round your answer to two decimal places. % in smaller section modulus =|
ure B 2m2 m C -2 m D 4 m 500 N 700 N 2 of 2 Part B Identify the zero-force members in the truss shown in (Figure 2). Check all that apply. 000 CD DE CG CF FG BC BG DF AG EF AB Submit Provide Feedback Request Answer
View Policies Current Attempt in Progress the automobile bumper jack is designed to support a 4640-N downward load. Begin with a free-body diagram of BCD and determine the force supported by roller C. Note that roller B does not contact the vertical column. E 155 mm Answer: C- Save for Luster 155 mm 430 mm 2690 mm 4640 N D N $105 mm 250 mm Attempts: 0 of 1 used Submit Answe
The rigid plate ABC shown in figure 2, was positioned on top of two identical steel posts, and the aluminum post was 0.1mm shorter than the steel posts at temperature of 50°C, if the allowable compressive stress in steel is limited to 120 MPa and in aluminum to 150 MPa, what is the maximum possible load P that can be supported on the rigid plate at temperature of 10°C ?
Problem 2 Consider the casting of the 2mm thick object below shown in its top view. If one riser with D =H = 6.5 mm is needed for this casting, illustrate where the riser should be located to produce a sound casting. Is this possible with no chills? Hint: use your illustration to justify. If no risers were used, illustrate where the shrinkage defects would likely occur. Tip: Using Word's/Powerpoint's basic shapes will be helpful here. 12.5 mm 10 mm 6.2 mm
An engineer is designing a beam to support a flooring system above it, as well as two walls. The beam will be a T-section, though the engineer is considering the idea of combining timber and steel to create a composite member for the application. The dimensions of the T-section beam are shown below: dw The dimensions of the T-section beam are shown below: bf Flange (horizontal section of cross-section): • bf = 340 mm tf = 15 mm ● Walls Flooring Beam
figure A 2m """" B 2 m C ** 2 m E 4 m D 700 N 500 N 2 of 2 > ▼ Part B Identify the zero-force members in the truss shown in (Figure 2). Check all that apply. EF FG ODF П П П □ DE AB ВС BC AG CG CD BG CF Submit Provide Feedback Request Answer
Question 16 For the loaded beam shown What is the lightest A36 steel W-shape from Appendix B of the textbook that can support the load without exceeding 24 ksi? (Note: answer needs to be entered for example as "W14x30" no spaces) 20 kip 10 kip 10 kip 10 kipm 5 ft 20 ft
A 15" x 3/8" bar of A572 Gr. 50 steel is used as a tension member. It is connected to a gusset plate with 7/8-in diameter bolts as shown in the figure. Use s = 2.0 and g = 3.0. Determine the allowable tensile strength of the section based on tensile rupture of the net area. Answer: о о lo O o
A pipe is supported at 10-foot intervals by a bent, threaded rod, as shown in the figure. If a 10-inch-diameter standard weight steel pipe full of water is used, what size A36 steel rod is used?a. Use LRFD.b. Use ASD.
130% v - + 7 Annotate T| Edit Trial expired Unlock Full Version ENGR 263 A A A EXERCISES Eleven sets of illustrations and the corresponding free-body diagrams of building-related beams were provided in Chapter 4 as Exercises 4. I through 4.11. These free-body diagrams constitute exercises that will be used here and again in Chapter 12. Follow these instructions carefully to save time later: (a) On each sheet of engineering paper reserved for analysis, calculate the vertical shear specific to that member at appropriate intervals across the length of the free-body diagram. Be sure to solve for locations where shear passes through zero. (b) On cach sheet of engineering paper containing the tree-body diagram, neatly draw the related shear diagram directly below the associated free-body diagram. The shear diagram should be located in the middle one-third of the page. Reserve the bottom one-third of the sheet for the bending moment diagram introduced in Chap- ter 12. Be sure to show…