then repeat

Q: 2- To balancing of rotation mass system of the same plane we need to addition two masses. * False…

A: AS PER COMPANY GUIDELINES, ONLY 1 QUESTION CAN BE SOLVED AT A POST. FOR SOLUTION OF OTHER QUESTIONS,…

Q: Q1. Determine the angular velocity (0) and angular acceleration (0) ofLink DC of the for bar linkage…

A: given dataN=100rpmω2=2πN60=2π×10060=10.47rad/sso, AB velocityV2=ω2×AB=0.47×400=4.2m/s ***Please note…

Q: 5- The purpose of balancing of rotating mass system is to avoid the vibrations. * False True

A: AS PER COMPANY GUIDELINES, ONLY 1 QUESTION CAN BE SOLVED AT A POST. FOR SOLUTION OF OTHER QUESTIONS,…

Q: harmonic motion during 120º of cam rotation, (b) Follower to dwell for the next 60°, (c) Follower to…

A:

Q: rad The rod OA rotates clockwise at a constant angular velocity of = (3) - Two pin-connected slider…

A: given data is

Q: Q6/ Draw the displacement diagram of a cam operating a knife-edge follower when the axis of the…

A: Given: Outward Stroke = 160° (uniform accelaeration)stroke = 50 mmdwell = 30°Return stroke =…

Q: а. The cam angular velocity. b. The cam rotation segment widths, ß1 c. The lift (height) of the…

A:

Q: aracceler eration

A:

Q: The instantaneous position of a four-bar linkage mechanism is shown in figure 1. The input link, AB,…

A: (a) To Draw: The velocity diagram describing this mechanism's motion. Showing magnitudes and…

Q: 2. The valve timing for a four stroke petrol engine is as follows: inlet open 4° L, inlet closes 50°…

A:

Q: Use the following parameters for displacement diagram of a cam using the motions, Constant Velocity,…

A: It is asked to draw a displacement diagram based on the following  data Accent 60 Descent 60 dwell…

Q: Searbox and compound train gear system are widely used in power transmission systems to change input…

A:

Q: ith a minimum radius of 15 mm that rotates counter clockwise. The motion of the knife edge follower…

A:

Q: For a plate cam with translating offset follower with knife-edge similar to the following Figure,…

A:

Q: The image below depicts one section of a cam shaft which opens a valve to release the pressure in…

A:

Q: A Cam-Follower system is sketched below (not to scale); H=0.8 cm; D=3.0 cm; d=1.0 cm, R=1.0 cm, and…

A: It is asked to calculate the angular velocity of the roller from the mechanism shown below H = 0.8…

Q: 21/ Draw the profile of a cam operating a knife-edge follower (when the axis of the follower passes…

A:

Q: Design a cam in non dimensional form consisting of 5 sections, each having the following…

A:

Q: Design a cam to move a follower from 22 mm height to 15 mm height in 60, fall an additional 15 mm in…

A:

Q: A cam rotating clockwise with a uniform speed is to give the roller follower of 20 mm diameter with…

A: Given Cam radius = 45 mm Offset = 15 mm Follower diameter = 20mm To find The cam profile

Q: Please can you show the working of 'Now fixing the angular velocity at 1.5 rad/s and crank length of…

A: 'Now fixing the angular velocity at 1.5 rad/s and crank length of 40 mm. by Changing the  crank…

Q: The image below depicts one section of a cam shaft which opens a valve to release the pressure in…

A:

Q: trajectory of the cutter centre to machine

A: Given; Trajectory of the cutter centre to machine the island   PQRS is ?Where,   Rectangular island…

Q: 2 rotates at a constant speed of 300 rpm in clockwise direction with the length of AB being 0,3 m.…

A:

Q: The four-bar mechanism is driven by a crank (Link AB) which rotates clockwise at 150 rpm. For the…

A:

Q: ond, rise of 5cm with cycloidal motion for another 2 seconds before dwell for half ond, then return…

A: Scaling in displacement diagram:X-axis 10 mm =30° [Horizontal axis]Cam angular displacement:Y-axis…

Q: A cam drives a radial, knife-edged follower through a 68 mm rise in 180° of cycloidal motion. Give…

A: Write the height of rise in a knife-edged follower.   L=68 mm   The angle moved by the cam in 68 mm…

Q: Given the following data: Follower type roller follower, off-set to the right by 5mm; lift 30mm;…

A:

Q: The rotation of a point particle at a specific time interval in a machine was studied and results…

A:

Q: 1.) The driving crank AB of a slotted lever quick return mechanism, as shown below, revolve at a…

A: Given: To find: Velocity of slider B Acceleration of slider B along the slotted lever PQ…

Q: A centrifuge in a medical research laboratory rotates at an angular speed of 3,750 rev/min. When…

A:

Q: A cam have the following specifications: Follower to move outward through 5 cm during 90° of cam…

A:

Q: 3,600° The instantaneous angular velocity of the crank Q2A is counterclockwise. Q2A = 1.5 in. Find…

A:

Workshop Math

Workshop technology is the application of scientific principles and methodologies for the manufacturing of machine components, tools, dies, etc. Workshop technology also provides the techniques, which can be carried out for metal joining and cutting processes. In a nutshell, workshop technology deals with metal works, and in a few cases, processing with plastics is also carried out. A mechanical workshop has seven major departments, each of the departments has sophisticated equipment and tools to carry out the manufacturing process. The major departments of mechanical workshops are plumbing shops, machining shops, carpentry shops, fitting shops, sheet metal shops, casting and foundry shops, and welding shops.