is total rise e is camshaft angle B is the

Q: isc SC

A: given:discuss how the cylindercal square is used?

Q: 3.00- 1.25-

A:

Q: v to find angle alpha??

A: To find angle alpha

Q: Is  this statment correct  Thick pearlite is not as strong as thin pearlite.

A: True , Thick(Coarse) pearlite do have less strength and hardness in comparison to thin(fine)…

Q: 5. What is the size of pattern? The size of pattern is different than size of casting b. The size of…

A: Pattern is defined as the replica of the casting to be produced which when placed in mould leads to…

Q: Briefly write down the  steps on how to generate (sketch) an involu

A: Involute Profile

Q: If the part was cut by this plane, what would the resulting remaining face look like?

A: Section planes in SketchUp cut a model along a plane so you may look within it without altering…

Q: Draw isometric view of casting, two views (FV and SV) of which are shown in figure in First 3. angle…

A: First draw the given front view and side view of casting.

Q: I didn't understand how you fond the angle teta

A: For solution refer below images.

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: Identify the following sectioning views (a, b, and c). a O Removed, Revolved and Removed O All…

A:

Q: The given figure shows a casted I shape made from steel. You are required to design a wooden pattern…

A: According to the details provided in the question, we need to create a pattern with steel. First, we…

Q: The ratio of the solidification time

A: Given; Solidification time of a casting is proportional to      ⇒    VA2where, v=volume A= total…

Q: The grinding wheel is made of aluminium oxide are bonded with cobalt. Select one: O True O False

A: Grinding wheel: It is a wheel composed of abrasive compound and it is used for various grinding and…

Q: Redraw when the rack AB is at 45o angle. What are the other two angles belonging to the triangle…

A:

Q: A shell of diameter = 600 mm Height of the shell= 300 mm Height with corner radius=D0.6 mm It is…

A: Given: Diameter of shell, d=600 mmheight of the shell, h=300 mmHeight with corner radius, r=0.6 mm

Q: Please sketch this in solidwork and find the surface area and volume. Take a screen shot and post it…

A: The model needs to be drawn on Solidworks and the surface area and volume has to be calculated

Q: What is the Neutral Axis?

A: The neutral axis is the fiber of the beam with no normal stress. When a beam is subjected to a…

Q: Is 2.0cm3 of aluminum same as 2.0cm3 of lead

A: According to the given data, the volume of the aluminum object is 2.0 cm³  and the volume of the…

Q: -450.76 for parts (c) and (d) are incorrect.

A: To determine:c)The gauge pressure at point 2d)The gauge pressure at point 3

Q: What is the symmetrical axis?

A: Axis of symmetric.  Axis of Symmetry is a line that Split the figure into two symmetrical sections…

Q: The diagram shows a 1 cm3 block that is divided into cubic millimetres. How many mm are there along…

A:

Q: Rc is -178.25 Ib. Why in the formula it's 17825 ?

A: The value of RC is represented as : Rc=-178,25 =-17825 lb The negative sign denote the direction…

Q: Determine blank diameter ?

A: Given;  Shell diameter, d= 300 mmHeight of the shell, h= 200 mm Corner radius,r= 0.4 mmThe shell is…

Q: PS Find Ter, Cower , P for Figure lower 1 below 9, 一E 2.

A:

Q: Can you pls slove this question briefly with hand written notes and diagram

A:

Q: Redraw when the rack AB is at 89o angle. What are the other two angles belonging to the triangle…

A: When the rack AB is at 89o angle. Draw the diagram as given above.

Q: (Find the angle By using Law of sine's when ( a= 50° , A=21.6 C=12 .A 24.57° .B 25 .c 25.15° .D 25°

A:

Q: The grinding wheel is made of aluminium oxide are bonded with cobalt. Select one: True O False

A:

Q: OK, so the EA = 108 N, Length (L) = 13 m, and the angle is 22.6. What now?

A: Here you are asking about what to do if the EA = 108 N, Length (L) = 13 m, and the angle is 22.6…

Q: Deleimine wasik done

A: Given data : The value of force applied=F The value of displacement=D   To find : Work done

Q: 4) At what temperature will Aluminum have 1017 vacancies per cubic centimeter.

A: First we will write all he properties of aluminium to solve the question.

Q: Where did you get the 3 from for the distance of q?

A:

Q: explain this mash

A: Given: To find: Explain the mesh

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.