The water tank as shown in the figure is being filled through section 1 at velocity of 5 m/s and through section 3 at flow rate of 0.012 m3/s. If water level varies and velocity at section 2 is 8 m/s, find the rate of change dh/dt. Assume d = 1.0m. O3=0.012 m3 D, 40mm D2:60 mm Water Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: m/s Decimal Places required in the final answer: 3

The water tank as shown in the figure is being filled through section 1 at velocity of 5 m/s and through section 3 at flow rate of 0.012 m3/s. If water level varies and velocity at section 2 is 8 m/s, find the rate of change dh/dt. Assume d = 1.0m. O3=0.012 m3 D, 40mm D2:60 mm Water Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: m/s Decimal Places required in the final answer: 3

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In a horizontal pipe water flows at a rate of 9.1 L/s. Here, the pipe has two sections, one with a diameter of 10.16 cm and the other with a diameter of 5.08 cm, with a gradual smooth reducing section. In this case, a mercury manometer is used to measure the pressure difference. If friction is negligible how would I find the differential height of mercury between the two sections? If the manometer on the 5.08cm pipe section was replaced with a pitot tube how would the reading change? any help would be deeply appreciated
Two pipes in a series have a flow rate of 50 L/s. The pipe upstream is 300 mm and reduced downstream to 150 mm. Determine the velocities for both diameters in m/s. Consider the centerline of the pipes along a horizontal datum reference. Ignore losses.
A uniform cross-sectional water tank is placed in a cart as shown in figure. The cart is mounted on frictionless rollers and the water is discharged to atmosphere through an attached nozzle. However, the the water level the tank is maintained at a constant height h above the nozzle by an external supply at a volumetric flow rate Q. The cart is restrained from moving by the cable seen in figure . The mass of the tank, cart and water is M. In terms of the parameters h, Aj and the water density ρρ. derive expressions for (a) the volumetric flow rate Q and (b) the tensile force T in the cable. (c) At time t = 0, the cable is cut, and the cart begins to move to the left at a velocity Vc{t} that increases with time. Derive an expression for Vc{t}.
Water flows into a tank and out through another pipe, as shown in the figure below. The water in the tank has a surface area, Asurf = 5.6 m². At the bottom of the tank there is a door inclined at an angle = 45 degrees with respect to the horizontal. The door has a length L = 0.9 m and a width w=0.8 m (out of the page). The flowrate into the tank is Q₁ (t) = 0.3 m³/s and the flowrate out is Qo(t) = 0.07 m 3/5 At time t = 0, the water has a depth ho = 2 m. The density of water is p = 1000 kg/m³. Asurf x h(t) a) Find the pressure (in kilopascals) at time t = 0 Qout
Figure 5 shows a pump connected to a large tank of water. Water flows out of the tank through the pump into a galvanized iron pipe of diameter D = 80 mm at a length, L = 40 m. At the end of the pipe, water exits through a nozzle of diameter D2 = 50 mm. With the height of water h, the pump adds 30 kW of power to the water resulting in a volumetric flowrate of Q=0.05 m³/s. Ignore the length of the nozzle and assume that the velocities are uniform. By using the same height of water and pipe, explain and justify with your calculation, which parameter(s) will be affected if the pump is to be removed from the system. ♡ (1) D2 = 50 mm h (2) Ритp L= 40 m D= 80 mm Figure 5
Water with density of 998 kg/m3 flows from a lake through a device inside the building at rate of 0.11 m³/s as shown in figure below. The piping system has length and diameter of 91.5 m, 0.12 m respectively. ● (1) Is the device inside the building a pump or a turbine? Justify your answer. Determine the horsepower of the ● device. Neglect all minor losses and assume the friction factor is 0.025. Lake Int 10 m
A pump with an efficiency of 89.842 percent delivers water at a rate of 13.79 m3/s but with a leakage loss of 0.5 m3/s. The friction losses within the pump result in a 1 m head loss. What is the total dynamic head of the pump in meters if it has a mechanical efficiency of 98 percent?
A pump at an elevation of 300m is pumping 0.05 m³/s of water through 2.4 km of 150-mm pipe to a reservoir whose level is at an elevation of 380m. What pressure will be found in the pipe at a point where the elevation is 335m above the datum and the distance (measured along the pipe) from the pipe is 970m? Compute the capacity of the pump. Use E/D= 1.5384x10-³
A liquid enters a diffuser at speed 10.8 feet/second. The diffuser's inlet diameter is 4 inches while it's outlet diameter is 6 inches. Determine the speed of the water at the diffuser outlet in feet/second.
A centrifugal pump driven by a 120-kW motor rotating at 2400 rpm is used to pump 20°C water in a manufacturing plant. The pump operates against a head of 30 m and has an efficiency of 70%. If this pump is situated 9 m below the level of the source, calculate (Zs)max and determine if the pump is safe from cavitation. Select one: O a. -7.9 m; NOT SAFE O b. -9.7 m; NOT SAFE O c. -7.9 m; SAFE O d. -9.7 m; SAFE
Water is pumped at a rate of 24.33 m/s from tank (A) and out through a 298.05 m pipe to tank (B). The surface roughness of the pipe is 0.046 mm. When the water levels are as shown in the given figure, the head provided by the pump is 70.54 m. Calculate the pipe diameter (mm) if the water temperature is 10°C (do not assume the water mass density and the viscosity). Use f = 0.02 for the first iteration and try only one more iterations (two in total) by using Swamee and Jain formula. Elevation Elevatjon - = 140 m = 135 m Tank (B) Elevation = 100 m Tank (A) pump Elevation = 95 m
A storm drain has a maximum capacity of 120 L/min. During heavy rains, an influx of 240 L/min approaches the drain. Assuming the drain is cylindrical, by how much would the drain radius need to be increased to handle the heavier rainfall? Assume the water travels at the same linear speed in both drains. The answer is 1.4. Please explain why A 16 times greater B 42 times greater C 2 times greater D 1.4 times greater