The water is flowing with a velocity of 1.5 m/s in a pipe of length 2500 m and diameter 500 mm. A valve is provided at the end of the pipe. What is the rise in pressure if the valve is closed in 25 seconds? (Take velocity of pressure wave is 1460 m/s) A) 15 N/cm 2 B) 1500 N/cm C) 150 N/cm D) 15 kN/cm 2 2 2

The water is flowing with a velocity of 1.5 m/s in a pipe of length 2500 m and diameter 500 mm. A valve is provided at the end of the pipe. What is the rise in pressure if the valve is closed in 25 seconds? (Take velocity of pressure wave is 1460 m/s) A) 15 N/cm 2 B) 1500 N/cm C) 150 N/cm D) 15 kN/cm 2 2 2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A venturi meter with a 10.16 cm throat installed in a 15.24 cm pipe which is inclined upward with an angle of 45 degrees to the horizontal. If the distance between pressure tape along the pipe is 1.5 m, the differential pressure is 70kpa and the water temperature is 70°C, what is the discharge of water in cubic meter per second? Assume coefficient of 0.985.
A pump is discharging 12 lit/sec ofwater through 100mm diameter smooth steel pipe. When the pump is 720 kPa, the discharge pipe is at a point 540m distant from the pump and 45m higher in elevation. a. What is the velocity of flow on the discharge side of the pump? b. Assumingf= 0.025, compute the head loss of the pipe. c. Compute the pressure expected in the discharge pipe. 2 45 m 540m - 100mm dia
Water flows at 1.52 m/sec from a reservoir into a 900 mm diameter steel pipe that is 2286 m long and has a thickness of 25 mm. find the water hammer pressure developed by closure of a valve at the end of the line if the closure time is 8 sec. the velocity (celerity) of a pressure wave C=1440m/s, modulus of elasticity of water = 200 MPa and that of steel is 200,000 Mpa. Answer: 868.2 kPa
Water is flowing in a 3 m wide rectangular channel. A hydraulic jump occurs and the flow upstream is 360 mm deep while the flow downstream from the jump is 1300 mm deep. A) Find the discharge flowing in the channel. B) Find the energy absorbed by the jump in kW. Please answer correctly
Water is flowing through a venturimeter shown. The difference in pressure between Point 1 (D = 4cm) and Point 2 (D = 2cm) is measured using open tubes. If h is 50cm, solve the velocity of flow at Point 1. h O 0.81m/s O 0.88m/s 2.02m/s O 1.29m/s
Q1(b) Water flows through a pipe with a diameter of 2 m. Stagnation and static pressures measured by pitot tube are 0.3 m and 0.25 m of water, respectively. Calculate the velocity of flow
Water at 20°C flows through a 300-mm-diameter pipe that discharg sphere as shown in Figure 4.61, When a partially open val the top of the pipe, the flow rate in the pipe is 0.2 m*s and the (gauge) pressure just upstream of the valve is 600 kPa. Estimate the force partially open valve, es into the atmo- ve extends 200 mm from exerted by the water on the —Valve 0.2 mYs —» Atmosphere Figure
Water is flowing in AF pipe (Figure 1) at a velocity of 2 m/s and a pressure of 102400 Pa, the pipe length is 100 m. If the water pressure needs to be at a pressure of 1.6 atm on a lower level. What should be the different in elevation between the upper and lower levels in order to achieve this pressure? Take the density of water 1000 kg/m3 and gravity is 9.81 m/s2, consider the energy loss.
An orifice having an area of 0.0003 m2 is located on the vertical side of a tank. The tank has a constant cross-sectional area of 0.40 m2. It takes 312 seconds to lower the head from 1.20 m to 0.60 m. Determine the following:a. Coefficient of dischargeb. The time to lower the head from 1.20 m to 0.80 m when C = 0.60.c. The head after 240 seconds from an initial head of 1.20 m when C = 0.60
Please solve in detail.