The venturi of a simple carburettor has a throat diameter 20 mm and the fuel orifice has a diameter of 1.12 mm. The level of petrol surface in the float chamber is 6 mm below the throat of venturi. The coefficient of discharge for venturi and fuel orifice are 0.85 and 0.78 respectively. Calculate (1) Air fuel ratio for the pressure drop of 0.08 bar. (ii) Petrol consumption in kg/hr.

Q: A treatment plant has a capacity of 2 mio. 1/d. Estimate the Camp number, size of the tank and power…

A: Given data  Capacity of treatment plant = 2 x 106 liter/day = 2000 m3/dayRetention Time = 1.5…

Q: The efficiency at the best operating point is:

A: The best operating point is that point at which a pump is least prone or least probable to failure…

Q: An engine has an inlet stagnation condition of 300 bar and 4000 kelvin. Methane and liquid oxygen…

A: Given: stagnation pressure = 300 bar stagnation temperature = 4000 K Ae/Ath = 34.34

Q: 40. 4.2. At what temperature and pressure would carbon monoxide, water vapor, and helium have the…

A: Given data: Ta=288 KPa=1 atm Need to determine the temperature and pressure would carbon monoxide,…

Q: Water (20°C, saturated) enters a 2 in. Sch. 40 pipe at a velocity of 1.0 m/s and a pressure of 1…

A: A pipe is given at some elevation to the ground and using Bernoulli's theorem we can solve this…

Q: Draw a simple flowchart of a hypothetical oxygen piping system containing the following components:…

A: The oxygen piping system follows this path:PSA generator creates oxygen.Compressor pressurizes the…

Q: A closed type injector has a nozzle orifice diameter of 0.949 mm and the maximum cross sectional…

A:

Q: clearance ratio of the compressor.

A: Given; Clearance volume of a reciprocating compressor,  Vc=120 mlVolume of the cylinder at bottom…

Q: True or False: -A diverging nozzle makes the velocity of fluids quicker -The temperature from 11 KM…

A: 1).False,by using continuity equation,A1V1=A2V2,here for diverging section A2 increases hence the…

Q: The operation of forcing additional air under pressure into the engine cylinder is known as,  (A)…

A: Given: The operation of forcing additional air under pressure into the engine cylinder is known as,

Q: Clearance volume of a reciprocating compressor is 300ml, and the volume of the cylinder at bottom…

A: The clearance ratio of the compressor is 3/17.

Q: A pitot tube and a static port on the fuselage skin is used to measure the velocity of the aircraft.…

A: Upstream of the pitot tube, the static pressure is the operating pressure in the pipe, duct, or…

Q: . Assess the different types of industrial compressor and identify justifiable applications for each…

A: The three most commonly used air compressors are reciprocating, rotational screw, and centrifugal.…

Q: 13.81 Consider the stagnation tube of Figure 13.6. If the uncer- tainty in the manometer measurement…

A: Given data CP = 1ρair = 1.25 kg/m3uncertainty in manometer measurement =∆ = ± 0.1 mm Given question…

Q: A Process fluid is pumped from the bottom of one distillation column to another, using a centrifugal…

A:

Q: A 5 in. x 4 in. double-acting simplex power pump is used to deliver water at 68oF. The pump operates…

A: Given data for double acting power pumpStroke length(L) = 5 inDiameter(D) = 4 inTemperature of…

Q: When ventilating the patient on a time-cycled/pressure-limited ventilator, what parameters determine…

A: For individuals who need help breathing, a mechanical ventilator known as a…

Q: using data given for a horizontal pipeline, predict the outlet pressure required to transport the…

A:

Q: Q1/ A simple jet carburetor is required to supply 0.1 kg/s of air and 8.333x10-3 kg/s of fuel of…

A:

Q: Assuming the clearance is negligible for a single stage compressor with the following data :…

A:

Q: r output of 368 low at 800 rpm. The fuel consumption is 0.238 kg/kwh. The pressure in the cylinder…

A:

Q: 80 of that of the choke. calcui

A:

Q: stroke oI

A:

Q: A closed type injector has a nozzle orifice diameter of 0.949 mm and the maximum cross sectional…

A: To find: The volume flow rate of fuel through the injector and the velocity of jet. Given: The…

Q: as density decreases, mass flow rate: a. de

A:

Q: 12.18 WEY The performance characteristics of a certain centrifu- gal pump having a 9-in.-diameter…

A:

Q: Problem 13.45 Air flows at 260 m/s through the pipe. The temperature is 400 K and the absolute…

A: Given Diameter 0.3 mVelocity 260 m/sTemperature 400 kStagnation pressure 280 kPaTo find out Pressure…

Q: 7. A four-stroke, 6-cylinder, 3.6 Itr SI engine, is designed to have a maximum speed of 6000 r.p.m…

A: Carburetion is defined as the mixture of proper amount of fuel with air prior to entering in the…

Q: A resistojet has a throat diameter of 0.3 mm and is to be operated with helium at a pressure of…

A: Solution: Given Data: dt=0.3 mmPi=1000 pside=3 mmTmax=1000 Kcpcv=γ=1.66   To Find: (a) The mass flow…

Q: at the d to be Ssumins

A:

Q: Problem 6: When you exhale 41 in five seconds through a trachea of 18 mm diameter, what is the…

A:

Q: Categorize air-compressor to dynamic and positive-displacing compressors and distinguish each main…

A: Hello. Since you have posted multiple questions and not specified which question needs to be solved,…

Q: Q.1 A 4-stroke, 4-cylinder diesel engine operating with bio-diesel fuel with an equivalent molecular…

A: THE SOOT AND CO EMISSIONS :Non-Dispersive Infra-Red (NDIR) technique: • This is the business…

Q: A pitot static tube fitted in a pipe of 0.25 m diameter records the difference in stagnation and…

A: Given question belongs to subject Fluid Mechanics and from the topic Pressure measurements.

Q: The diameter of the pipe is 100 mm and velocity of oil (SG=0.89) is found to be 3,4 m/s. 32.…

A:

Q: A pneumatic vacuum lift system has a total volume of 15 ft³ inside the cup and associated pipeline…

A: GIVEN DATA-

Q: A simple jet carburetor is required to supply 5 kg of air and 0.5 kg of fuel per minute. The fuel…

A:

Q: The water level in a tank is 34 ft above the ground. A hose is connected to the bottom of the tank…

A:

Q: .Calculate the volumetric flow through nozzle meter if; Nozzle w coefficient (a) and Nozzle…

A:

Q: veločily öl air Of vhen the nozzle tip is providled.

A:

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.