The uniform 18-m pole has a mass of 125 kg and is supported by its smooth ends against the vertical walls and by the tension Tin the vertical cable. Compute the magnitudes of the reactions at A and B. B T 12 m 6 m A 15 m Answers: FA- FB= i N

Q: In a vehicle when it is turned the axis of the wheel on the inside of curve turns through 45° angle…

A: Given data: -  The angle of the inside wheel is θ = 45o. The angle of outside wheel is φ = 30o. The…

Q: 2. If Tc= (-5) find TF. TK and TR.

A: Given:  TC=-5

Q: From the the double slider-crank mechanism shown in Fig.A (a) Determine the number of Instantaneous…

A:

Q: 소 6 ㅅ

A: To draw a rotating coordinate system then moves with a pendulum

Q: Direction. Draw the Force Sody Diagram of he tollowing iustrations. Lund

A: Draw the free body diagram for the given figures.

Q: Given the following data, draw in a cartesian plane, the resulting vector,and it's three director…

A:

Q: 2.3. Outrigger

A: Given Data: Diagram of an outrigger

Q: Find the distance traveled by the slider if connecting rod is 10 inches, cranks is 30 deg (past top…

A:

Q: find closure Eq.

A: You have mentoned the postions and angles .

Q: Fill in the following blanks 1. -----------Form of programmable automation in which the mechanical…

A: 1.Numerical Control Form of programmable automation in which the mechanical actions of a machine…

Q: Question Figure Q1 shows the schematic diagram of a moulding press, which is driven by a crank BC…

A: Figure Q1 shows the schematic diagram of a moulding press, which is driven by a crank BC rotating…

Q: Don't Use Chat GPT Will Upvote And Give Solution In 30 Minutes Please

A: Step 1:Given:The force acting perpendicular to the road and at the left end of the stick is F1​.The…

Q: Write a list of the therbligs that comprise this motion sequence and label each basic motion with a…

A: Given:  A plumber, kneeling on the floor next to the sink To write: a list of the therbligs that…

Q: Answer the following in the space provided. 39. Suppose the engine in a vehicle is delivering 550…

A: Data given-  T1 = 550 lb -ft  N1 = 5000 rpm  Gear ratio = 1.5/ 1 = 1.5

Q: 3. if you had to lift a truck and had a pole, a rope and a fulcrum, you could do it! A kid could do…

A: for third kind of lever fulcrum lies at one end and object other...

Q: 1. Find the degrees of freedom of the following two different inks Pin in slot a. b.

A: DEGREE OF FREEDOM (DOF) The freedom degree is defined as the minimum number of independent variables…

Q: If the hydraulic cylinder at H draws rod BC in by a distance d = 4.545 in, how far does the slider…

A:

Q: The engine room of a freighter is on fre A frefghting tugboat has drawn along sde and is drecting a…

A:

Q: Determine the following for point C on the slide if the angle theta measures 45 degrees and the BC…

A:

Q: A system is equivalent if the_ those caused by the original force and couple moment system it…

A: Given System under force To find Verify the system

Q: Problem 2 a) Locate and mark the instantaneous center of zero velocity with "IC" on the picture.. b)…

A: Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: Draw the free-body diagram for the boom. Connection at A is a pin. Draw the vectors starting at the…

A: To draw: Free body diagram of the boom. Given: The connection at A is pin. Sketch: The force In wire…

Q: With the help of a sketch illustrate the pitch, yaw and roll motion of a robot wrist.

A: Given:- Robot wrist to illustrate the pitch, yaw and roll motion

Q: Each section of the pipe assembly ABDEC is is parallel to one of the coordinate axes. The force F…

A:

Q: 8. Three ships A, B, C are located as follows: A is 48 km due north of B and C is 125 km due east of…

A:

Q: FIND THE DEGREES OF FLEDOM OF THE MECHANSNE.

A:

Q: The magnitude of a vector: a.Can be positive or negative. b.Must always be negative. c. Must…

A: The magnitude of a vector: Answer: c. Must always be positive.

Q: What is the vertical component of the velocity of point B? Let a positive velocity be up What is…

A:

Q: Hello, I need help with the answer of 3.14 from the picture, please.

A:

Q: EXAMPLE TL ROBOT - In a TL robot, assume that the origin of global coordinate system is at J2 ·…

A: Power source for robots are :1.) Hydraulic drive: It will gives a great speed and strength to the…

Q: If an inlined plane has an IMA of 8, an output force of 160N and an input force of32oN what is the…

A: Given Data:To Find: IMA: Ideal Mechaincal AdvantageAMA: Actual Mechaincal Advantage

Q: Find the oxthagonal r-6a.Cose whese a is pasametes

A: r=6acosθWhere a is a parameter Now need to calculate orthogonal trajectory

Q: Use the image below to do the following  i.  draw 3 positions on a piece of paper. ii.  Chose a…

A: Find three positions and corresponding distances based on the reference point.Alos find linear…

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.