The two bars are used to support load P. When unloaded, joint B has coordinates (0, 0). After load P is applied, joint B moves to the coordinate position (-0.65 in., -0.20 in.). Assume a = 18 ft, b = 36 ft, c = 12 ft, and d = 24 ft. Determine the normal strain in each bar.

The two bars are used to support load P. When unloaded, joint B has coordinates (0, 0). After load P is applied, joint B moves to the coordinate position (-0.65 in., -0.20 in.). Assume a = 18 ft, b = 36 ft, c = 12 ft, and d = 24 ft. Determine the normal strain in each bar.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

If the allowable bearing stress for the material under the supports at A and B is Ob = 780 psi, determine the maximum load Pmax that can be applied to the beam. The bearing plates each have square cross sections of 5 in. by 5 in. The reactions at the supports are vertical. Assume w = 600 lb/ft, a = 12 ft, and b = 6 ft. Answer: Pmax= i W a B b lb P
I want the correct solution with proper explanation.
1. We have a truss structure with a hinge on the left and a roller on the right. (Use method of moments ONLY for finding the members and use the numbered name only for each member) 30.00" a) Find the force acting on members 2, 3, 7, 9, 14, 15. (Indicate Compression or Tension) b) Determine the normal stress @ members 2, 3, 7, 9. (Use figure 2 for cross-sectional area) P/2 30.00" T IP 30.00" T Figure 1 30.00" P/2 30.00" P/2 10.00" 20.00" 2.00" 0.20" Figure 2 0.20" 2.00" 0.20"!
1. We have a truss structure with a hinge on the left and a roller on the right. (Use method of moments ONLY for finding the members and use the numbered name only for each member) 30.00" a) Find the force acting on members 2, 3, 7, 9, 14, 15. (Indicate Compression or Tension) b) Determine the normal stress @ members 2, 3, 7, 9. (Use figure 2 for cross-sectional area) P/2 30.00" D foo 30.00" Figure 1 30.00" (10 N -30.00" P/2 P/2 10.00" 20.00" 2.00" 0.20" Figure 2 0.20" 2.00" 0.20"
The two bars are used to support load P. When unloaded, joint B has coordinates (0, 0). After load P is applied, joint B moves to the coordinate position (-0.46 in., -0.20 in.). Assume a = 15 ft, b = 30 ft, c = 10 ft, and d = 20 ft. Determine the normal strain in each bar. A Answer: EAB EBC = i i P a (1) B με με X b (2) C d
A pin-jointed truss ABC shown below consists of two links AB and BC. These links are 6 mm thick and 20 mm wide as shown. There are support brackets at A and C. All pins are 12 mm in diameter and a vertical force, P = 9 kN is applied at pin B as shown. The angle 0 =38 deg. and the angle ẞ = 0 + 20 deg. The normal stress in link AB is (The result is accurate to one decimal place, in the unit MPa. Please write down only the value of your final result) · 12mm 9 20mm -1.0m⋅ B
1. A stepped shaft is shown, the region AB is aluminum having G = 28 GPa, and the region BC is steel, having G= 80 GPa. The aluminum portion is of solid circular cross section 45 mm diameter, and the steel region is circular with 60 mm outside diameter and 30 mm inside diameter. A clockwise torsional load of 4000 N-m is applied at B, assume ends A and Care rigidly clamped. De termine the following: a. maximum shearing stress in the aluminum b. maximum she aring stress in the steel (
A simple pin-connected truss is loaded and supported as shown. The truss is constructed from three aluminum members, each having a cross-sectional area of A = 1160 mm2. Assume a = 2.3 m, b = 6.8 m, and c = 2.8 m. If P = 50 kN and Q = 75 kN, determine the normal stress in each member. L. Answers: JAB OBC i i JAC= i P b MPa (C) MPa (T) MPa (T)
The two bars are used to support load P. When unloaded, joint B has coordinates (0,0). After load P is applied, joint B moves to the coordinate position (-0.65 in., -0.10 in.). Assume a = 20 ft, b = 40 ft, c = 14 ft, and d = 28 ft. Determine the normal strain in each bar. a b C (2) (1) Answer: EAB = i &BC= i P B με με d
Determine the forces in members BC and CG. The forces are positive if in tension, negative if in compression. A 30 kips Answers: BC= CG= 10' i i B 10' C 10' D 12' 比 69° G SE E kips kips