The two 6.7° wedges shown are used to adjust the position of the column under a vertical load F of 7.4 kN. Determine the magnitude of the forces P required to raise the column if the coefficient of friction for all surfaces is 0.29. Assume 0 = 6.7° Ө Answer: P = i F Ө kN

Q: A circular steel shaft with length, L (m) has an outer diameter, d2 (mm) and inner diameter, d1…

A: Given data in question  Diameter  Modulus of rigidity Length Torque To find out  Torsional shear…

Q: A rectangular gate AB in Figure 1 is 1.2 m long and 0.8 m into the paper. Neglecting atmospheric…

A: To find hydrostatic force

Q: 1. Determine the vertical displacement of joint A if members AB and BC experience a temperature…

A: The method of virtual work can be used to determine the displacement of joint A in the truss due to…

Q: NOTE: This is à multi-part question. Once an answer is submined, you will be unable to retum to this…

A:

Q: 86

A: Approach to solving the question: Detailed explanation:Examples: Key references:

Q: с a=1m P L= 3 m- B The deflection at point Cis I W150 x 18.0 15.6 mm. ↓

A:

Q: 5. Blocks A, B, and C have weights of 50 N, 25 N, and 15 N, respectively. Determine the smallest…

A: Step 1: The smallest force P occurs when there is impending motion (impending slipping) between…

Q: Situation 6: Determine the smallest horizontal force P required to lift the 200-kg crate. The…

A:

Q: The wedge in the figure below is used to level the member. Determine the horizontal force P that…

A: To determine the horizontal force (P) required to move the wedge forward fro the given system with…

Q: The two 6.0° wedges shown are used to adjust the position of the column under a vertical load F of…

A:

Q: prevent a load (weight W) from falling downwards. The drum can rotate without friction about point…

A:

Q: 11. As shown in the figure below, a rectangular beam is subjected to two concentrated forces.…

A: Data given Find : Calculate the maximum normal stress and maximum shear stress at point Q cut at C…

Q: 532

A: Let's go through the problem step-by-step to compute the horizontal reaction force at point A on…

Q: Q2) The figure shows a cantilever consisting of steel channel size 127 mm×64 mm. Using…

A: Answer We know that the Superposition principle says that the effect of  combined loading is equal…

Q: Calculate the horizontal displacement of point B. EI is constant for all members (p=50kN , W=90KN/m…

A: The formula for ,deflection from unit load method =∑∫1nMm dsEInwhere, M is the bending moment due to…

Q: 3. The 180 lb man climbs up the ladder and stops at the position shown after he senses that the…

A: Free body diagram of given question

Q: = For the beam shown, calculate the beam slope at A. Assume that a = 41 in., b= 147 in., c = 63 in.,…

A:

Q: For the beam shown below, where: L1=6 m . L2=2 m P₁=15 kN . P2=6 kN Compute the vertical…

A: A simply supported beam supported at A and B of span L1 and an overhang portion L2. Two-point loads…

Q: Q.2) Determine the magnitudes of forces P and Q acting on the block so that the resultant of all…

A:

Q: Problem 1. Determine the smallest force P needed to lift block B. The coefficient of static friction…

A: Coefficient of static friction We all know that frictional force resists motion and is defined as…

Q: 1. Use the mass of the box at the right equals 50 kg. The coefficient of static friction between…

A: Figure is as shown

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.