The triangular block as shown in the figure is subjected to the load P = 600 N. If AB = BC = 6 m., resolve the load into components normal and tangential to AC. 8 m and A P=600 N В

Q: 2.5 0, L = 5.0 mH, and C = 500 pF. What is the angular frequency of the oscillations (in

A:

Q: In the given circuit a > w i-e overdamped case. Adjust the value of R for critical damped and…

A:

Q: 1 y" + 3y = 18x², y(0) = -3, (0) = 0 2 y + 4y + 4y = e- 2 sin 2x, y(0) = 1. (0) = -1.5 3 Find the…

A:

Q: A mass of 1400 kg rests on an oak beam. The beam rests on 200-mm diameter rollers. Assuming the…

A: Given: Mass, m = 1400 kg. Diameter of the rollers, d = 200 mm. Coefficient of rolling resistance…

Q: A 12.6 inches long key is to be used on a 210 hp, 1200 rpm, slip ring induction motor. The key is 1…

A:

Q: Question a) A stepper motor has a step angle of 1.8° and it is driven at 6500 pps. Analyzing the…

A:

Q: At what dislance is the KE. Of paulticle . af performing SHM. 'amplilāde locm, three Times is…

A: Have a look

Q: A  1550−kg automobile has a wheel base (the didtance between the axies) of 2.90 m. The automobile's…

A: Mass of automobile is m=1550 kg The distance between axle L=2.90 m The automobile's center of mass…

Q: One end of a uniform4.0-m-long rod of weightw is supported by a cableat an angle of θ = 37° withthe…

A: Given:μs = 0.50Length of the rod, L = 4m

Q: A 60 Hz power line has an angular frequency “ω” (in rad/s) of:

A:

Q: Compute for the total current flowing through the entire circuit.

A:

Q: A 100MVA, 50HZ turbo generator operates at no load at 3000 rpm. A load of 25MW is suddenly applied…

A: Hey dear have a look

Q: R- 1n J-29 33/11 kV 20 MVA 15% Calculate the voltage the On Load Tap Changer should maintain at…

A:

Q: A 50 Hz, 4 pole turbo generator rated at 20 MVA, and 13.2 kV, with an inertia constant of 9…

A: Power system in physics.

Q: n ΔABC, given that AB=15 m, BC = 8 m, and <B = 24 degrees, what is the length of side AC?

A:

Q: How do you get the I0 = 10^-12 W/m^2 ?

A: Sound intensity level is given by formula:β=10log(II0)Here,β is sound intensity level.I is…

Q: Determine the magnitude and direction of Ra, Rb and Rc for the truss shown.

A: The distance between two consecutive joints is equal. Therefore, assume the length between two…

Q: 8. Find the interval of convergence zk - ดู + sk 32 – x h + for the series

A: The interval of convergence can be calculate as fallowing by ratio test.

Q: If the angular velocity of sinusoidal voltage is 314 rad/s, then the periodic time is

A: Given that:Angular velocity is ω=314 rad/s

Q: In an oscillating RLC circuit, R = 5.0ohm, L = 5.0 mH, and C = 500 uF. What is the angular frequency…

A:

Q: For the circuit shown in figure, the capacitance C= 10µF, and the feedback resistance R 20 kn If the…

A:

Q: when snd twe reiton having Connected tesistance Ria desistances R. shms Rrohmi furalled, their is =…

A: Introduction: In the parallel connection of resistance, the terminal of the resistances are at the…

Q: 0 Find the voltage vo(t) in the circuit of Fig. by means of the Laplace transform. 1Ω 10u(t) A 0.5 F…

A:

Q: 3 m 2 m F = 4i + 12 j- 3k 1- What is unic vector along AC line given in the above figüre? eac = 0.8i…

A:

Q: The motor in Problem 15.2 drives a load characterised by the relation T₁ = ko where T, is the shaft…

A: Solution:-                    Problem 15.2 in given     3-phase ,so 30 kw ,400 v,…

Q: he arm of a crane has a mass of 500 kg and a length of 12 m. It is inclined at an angle of 50…

A:

Q: 1. Given the following apparent power, what is the reactive power, in VAR? S = 4.2 VA θ = π/7…

A:

Q: How was I1 and I2 calculated?

A: Given:- A KVl equation with solution  Find:-  How the I1 and I2  find?

Q: Find the amplitude V the angular velocity w and the phase shift & for the sinusoidal voltage v(t) =…

A: We have a sinusoidal voltage which is given by v(t)=Vsin(wt+δ) where V is the amplitude, w is the…

Q: An L-R-C series circuit has L = 0.800 H and C = 9.00 μF. Calculate the angular frequency of…

A:

Q: An L-R-C series circuit has L = 0.300 H and C = 4.00 uF. What value of R gives critical damping?…

A: The objective of the question is to find the value of R that gives critical damping in an L-R-C…

Q: Use block diagram reduction techniques and find closed loop transfer function of the system whose…

A:

Q: A pick and Place machine is being used to perform the following sequence when the "Start" pushbutton…

A: Given: The arm is extended (out) by energizing a solenoid valve; when the valve is de-energizes, the…

Q: at 0.85 pf lagging.

A: Given: The figure and values are given as, fNL =51.1 Hz,Sp =1 MW/Hz,Load 1=1100 KW at 0.8 pf,Load…

Q: In Figure shown, the cg of the pole held by the pole vaulter is 2.00 m from the left hand, and the…

A: The free body diagram of the left hand of a pole is as follows: The net force acting on the pole is…