n ΔABC, given that AB=15 m, BC = 8 m, and

Q: (a) An RLC circuit is used in a radio to tune into an FM station broadcasting at f = 99.7 MHz. The…

A: At resonance,  inductive reactance = capacitive reactance wL = 1 / wC capacitance, C = 1/ L w2…

Q: Assume that i(t) = t(12 - t) A (tin seconds). Calculate the flux <l>(t), at time t, of B…

A: We are given current. We first find the flux through the rectangular loop. This is done by first…

Q: Your dual-band mobile phone can transmit at frequencies fi 800 MHz and f MHz. The phone transmits at…

A:

Q: The switch in the figure is closed on a at time t = 0. What is the ratio εL/ε (a) just after t = 0…

A: A series RL circuit consists of a DC resistance R and an inductor L connected across a power source…

Q: P+ T2 n the figure shown above, the magnetic dis uniform and into the page inside a ular region of…

A:

Q: The switch has been in position a for a long time. At t= 0, it moves to position b. Calculate (t for…

A: This circuit is an RC circuit. When the switch is at a fro a long time the capacitor will become…

Q: *3-15. The cylinder D has a mass of 20 kg. If a force of F = 100 N is applied horizontally to the…

A:

Q: WR b. The power (P) supplied to an electric circuit is given by P i? dt. If i = 63 * I sin(wt), I is…

A: P=ωR2π∫02πωi2dtGiven that,i=63×Isinωt

Q: (a) A physicist is constructing a solenoid. She has a roll of insulated copper wire and a power…

A:

Q: Assuming that a metallic rectangular waveguide whose cross-section is a × b such that a > b and it…

A: In a rectangular waveguide, the transverse electric (TE) modes are solutions to the wave equation,…

Q: Shown is the cross section of a solid wire carrying a uniformly distributed current, I, out of the…

A: And

Q: The four points A, B, C, D have position vectors pi, j+qk, k, and i+j respectively, where p and q…

A:

Q: In Fig. 13-21 a radial conductor, 3 ≤ r ≤ 6 cm, is shown embedded in a rotating glass disk. Two 11.2…

A:

Q: (a) In the figure what value must R have if the current in the circuit is to be 1.3 mA? Take ₁ = 2.7…

A:

Q: ctricity Grade 11 and 12: Exam 09 4 Ω V₁ V₂ A2 0,6 A r=0,8Q 5,8 Q 1. Determine V1? (2) 2. Determine…

A: Step 1: Step 2:

Q: Find the steady-state charge q (t) and the steady-state current i(t) in an LRC-series circuit when L…

A: See below

Q: P.11-3 A small filamentary rectangular loop of dimensions L, and L, lies in the xy-plane with its…

A: Let I be defined as the current, and A be defined as the area of the loop. Then, the magnetic moment…

Q: 4. Fill out the table of values based on the given closed circuit. Use prefixes as needed. Show all…

A:

Q: We use the general form of Faraday's law fē· ²-d and consider a circular integration path of radius…

A: The following equation is to be simplified:

Q: 3. Fill out the table of values based on the given closed circuit. Use prefixes as needed. Show all…

A:

Q: A solid cylindrical wire of radius a carries current / in the positive z direction. The wire…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: A water molecule and a neutral carbon atom are initially 8.1 x 10-6 m apart (about 81000 atomic…

A: The polarizability force is given by:Where:Substituting these values into the formula:

Q: In the circuit of the figure & = 3.90 kV, C = 7.50 µF, R1 = R2 = R3 = 0.830 M2. With C completely…

A: At t=0 , when the capacitor is uncharged, the potential across it is 0 and it acts as a short, as…

Q: A sinusoidally oscillating current ?(?)I(t) with an amplitude of 7.55 A7.55 A and a frequency of 775…

A:

Q: a) A student is experimenting with some insulated copper wire and a power supply. She winds a single…

A: The number of turns in the solenoid is, N=ld=90 cm0.1 cm=900 turns The number of turns per unit…

Q: Consider the circuit below. C, = 200 mF R, = 11 kn EV = 24 V R, = 11 kQ EV - 24 V R = 33 kn R, = 33…

A:

Mechanical Properties of Solids

There are three types of matter- solid, liquid and gas. Out of them, solids have a rigid shaped and size. The intermolecular forces of attractions in solids are greatest. Mechanical properties are the physical properties of a material which it shows, when it is provided with certain amount of force or load. These properties are to be kept in mind for various purposes. When a force is applied to an object, the object may or may not get deformed depending upon its elastic property. But every time the object develops a restoring force against the force applied. This is commonly known as stress. If the object changes its dimensions due to the force applied it develops strain ( which is the ratio of change in dimension to the original dimension).