The tractor shovel shown (Figure 4) carries a 530 kgkg load that has its center of mass at H. The shovel’s dimensions are: a = 51.0 mmmm, b = 204 mmmm, c = 306 mmmm, d = 102 mmmm, and e = 357 mmmm. Find the reaction force at E. Assume that the positive direction of the x and y axes is to the right and upward, respectively.

Q: For this problem, take a look at Figure 2. Assume that the rod is massless, perfectly rigid, and…

A:

Q: Şekildeki kütle bir AC kablosu ve AB yayı ile şekildeki gibi dengede durmaktadır. Yay katsayısı…

A: For the given condition ,

Q: The frame in the figure is a counter-balance scale used for decades to offer products. Calculate the…

A: Given data, The distance of EFG is 350 mm. Value of b= 200 mm x varies from 10 mm to 400 mm. Mass of…

Q: Please draw the picture of this problem and solve it. A uniform rigid disk has mass M and radius…

A: To determine the force to pull rod and disc apart, given mass of the disc mass of the rod  radius of…

Q: FEA 1-D Direct Method Bar Elements. A 1-D bar element system is Problem 3 connected as shown below.…

A:

Q: Given the figure at the right, find the resultant of F1 and F2 (in vector form)

A:

Q: Required information The figure shows a weapon called a battering ram (modern large battering rams…

A:

Q: kg ånd thE the moment of intertia about Z axis.

A: calculate the mass moment of inertia about z axis at a distance x=0.4

Q: Horizontal cantilever shart with disks is loaded by 2 concentrated forces. 1 F1 Given: 1=26cm;…

A:

Q: a=1850 I f=100 A b=750 C B O c=67 dimensions en mm d=990 X ✓e=594

A:

Q: A bar is attached to the spring at the point C. The left end of the bar is pin supported and can…

A:

Q: 4.An overhang beam is applied with a uniformly distributed load as shown in Figure Q4. a. Derive an…

A:

Q: - 3.3 m supported at its left The figure shows a horizontal beam of mass M = 22 kg and length L end…

A:

Q: The body in the figure is pivoted at O. Three forces act on it in the directions shown: FA = 8.80N…

A: Torque = Force x perpendicular distance from point of application

Q: Question 3: the bearing response forces at point A and the pulling force acting on the BC cable (T)…

A: Given: mass of AB =100 kg/m To determine: Intensity at bearing A Tension T

Q: The rectangular framework is subjected to the following non-concurrent system of forces: a 30lb-…

A: Mechanical Equilibrium: A body is said to be in mechanical equilibrium if it satisfies the following…

Q: The following figure shows a 4 m bar fixed to the wall through a hinge that rotates freely, but is…

A:

Q: D y

A: β=tan-12+OC cosθ6-OCsinθ=tan-12+2.8cosθ6-2.8sinθl=2×4.2×sinθ2=8.4sinθ2hences=l-2=8.4sinθ2-2moment of…

Q: Use stiffness influence coefficients to derive the stiffness matrix for A massless rod and other…

A: From the system given , Equation of motion for slender bar…

Q: The static moment of the connecting rod force F in relation to the pivot point O of the crank should…

A:

Q: The object that was horizontal before deformation, both shifted downward after the deformation and…

A: GIVEN:The object is horizontal initially before elongation. After elongation the angle made by the…

Q: Consider the square plate ABCD shown in the figure to the right whose rotation is about an axis…

A: We are tasked to find out the torque  due to each force  the net torque on the system Counter force…

Q: Q5/ Does this machine shown in the figure below maximize or mini find the reaction forces at point…

A: Force applied,FTo determine:Reaction force at A

Q: The système have diferent stiffness (K1 and K2), The column (AB) have both ends pined and the Beam…

A: From the given data:

Q: The traffic light shown below is supported by a system of cables. Points A and B are in a vertical…

A:

Q: A wheel radius 0.4meter has mass 3kg se figure. Center of wheel goes a rope to point A, the wheel…

A:

Q: For this problem, take a look at Figure 2. Assume that the rod is massless, perfectly rigid, and…

A:

Q: A beam of length L and mass M rests on two pivots. The first pivot is at the left end, taken as the…

A:

Q: ing and a rope that runs over a stationary pulley at point D (neglect the dimensions of the pulley).…

A:

Q: The bar below is 8 meters long and has a 37° 'F=500N negligible mass Three external forces act on it…

A:

Q: The tractor shovel shown (Figure 4) carries a 500 kg load that has its center of mass at H. The…

A:

Q: Part D -A tractor shovel The tractor shovel shown (Figure 4) carries a 550 kg load that has its…

A:

Q: 4. The system on the right consists of three solid circular cross-section rods 1, 2 and 3. All are…

A: Given: The load at D, F1 = P The load at C, F2 = 2P

Q: A heavy spool rests on the ground at point A and against the wall at point B. Find force F required…

A: Given that, Mass of the spool, m=100 kg,Radius of spool, ri=200 mm, and ro=460 mm,Coefficient of…

Q: A bar is attached to the spring at the point C. The left end of the bar is pin supported and can…

A:

Q: A bar is attached to the spring at the point C. The left end of the bar is pin supported and can…

A:

Q: 2.5 m 5 m 7.5 m 5 m K 10 m 5 m K K K 20 m Obtain the center of stiffness

A: For solution refer below images.

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.