The time required to saw a rectangular piece of stainless steel plate 3.5 meters long and 2.25 meters wide is 3/4 hour. the average feed per stroke of hacksaw is 0.25 mm. Calculate the required speed of the power saw in rpm in doing the crosswise cutting operation if the thickness is 25 mm. 4 O 125 200 O 150 O 175

The time required to saw a rectangular piece of stainless steel plate 3.5 meters long and 2.25 meters wide is 3/4 hour. the average feed per stroke of hacksaw is 0.25 mm. Calculate the required speed of the power saw in rpm in doing the crosswise cutting operation if the thickness is 25 mm. 4 O 125 200 O 150 O 175

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q5/A/ 125 mm long, 10 mm diameter stainless steel rod is being reduced in diameter to 9 mm by turning on a lathe. The spindle rotates at N= 360 rpm, and the tool is traveling at an feed of 0.49 mm/rev. Calculate the cutting speed in units (m/s), MRR, and cutting time.
A straight turning operation is carried out using a single point cutting tool on an AISI 1020 steel rod. The feed is 0.2 mm/rev and the depth of cut is o.5 mm. The tool has a side cutting edge angle of 60°. The uncut chip thickness (in mm) is .. . ... ...
the rod to 16 mm and also facing operation on both sides is done. Assume cutting speed is 30 m/min and a feed of 0.7 mm/rev is used. A mild steel rod having 35 mm diameter and 120 mm length is to be turned on a lathe. Determine the machining time to reduce 20 40 60 035 025 016
How much machining time required to turn a mild steel rod from 65mm to 58 mm over a length of 100 mm by turning using a carbide insert. If the approach length and over run length is = 5 mm, Cutting speed is 20 m/min and feed is =0.2 mm/rev, and the depth of cut is 0.5mm D
b) A mild steel having length of 350mm and diameter of 12.5 cm, is being reduced to diameter 9.5 cm, for the length of 22cm by turning on lathe, with a spindle speed of 250rpm. Assume feed (f) 2.5 mm/rev and 2 passes to complete the turning operation. Write the formula and calculate (i) Cutting speed (ii) Depth of cut.
How long will it take to saw a rectangular piece of aluminum plate 8 inches wide and 1.5 inch thick if the length of the cut is 8 inches, the power hacksaw makes 120 rev/min and average feed per stroke is 0.0060 inch?
The tool life equation for HSS tool is VTO.14f 0.7d0.4 = Constant. The tool life (T) of 30 min is obtained using the following cutting conditions: V = 45 m/min, f = 0.35 mm, d = 2.0 mm If speed (V), feed (f) and depth of cut (d) are increased individually by 25%, the tool life
Calculate the machining time to drill four 20 mm diameter holes and one 50 mm diameter central hole in the flange as shown below. Take cutting speed 20 m/min, feed for 20 mm drill 0.2 mm/rev, and for 50 mm drill feed is 0.6 mm/rev, the point angle is 120°? VIVER 20xA 200 D100 SYLON 50
A 450 mm long work piece is finished using a face milling cutter with a diameter of 75 mm. The overrun is 4 mm and the cutting depth of 3 mm. Calculate the total milling length.
Calculate amount of removed chips in (m³/min), If you have cutting width is 50mm, cutting depth is 10mm and .Feed speed is 4.15 mm/min 1.99 m³/min O 3.099 m³/min 2.075 m³/min O
i need the answer quickly
In turning of stales steel alloy, 1100 mm length and 400 mm diameter, the Feed was 0.35 mm/rev, and depth of cut = 2.5 mm. The tool used in this cutting is cemented carbide tool where Taylor tool life parameters are n = 0.24 and C = 450 (tool life (min) and cutting speed (m/min). Compute the cutting speed that will allow the tool life to be 10% longer than the machining time for this part.