The synchronous generator in Figure 2 is operating at rated MVA and at . PU 5% above rated voltage when a bolted three-phase short circuit occurs at bus 1. (1)Draw the equivalent circuit of Figure 2;(2)Calculate subtransient fault current, subtransient generator and motor currents, neglecting prefault current (including per unit value and real value). ( T1 T2 bus2 bus 1 100MVA L +0+ ++ 10kV X=0.20 X=0.15 100MVA (base on 100MVA 10.5kV), 100MVA 10.5kV 100MVA 110kV/10.5kV 10.5kV/121kV 100MVA 10kV X=0.15 X=0.10 X=0.10 X=0.20 Figure 2 M M

Q: fault location

A: Types of open circuit fault- 1) Symmetrical fault- Three phase line to ground fault  Three phase…

Q: A fault occurs at bus 4 of the network shown in Figure Q3. Pre-fault nodal voltages throughout the…

A: x=1y=7Note: reactance of element right to bus 4 is not given. Hence we will not consider that in…

Q: pecified in per unit. For generators, assume Z* =Z` =j0.2, Z° = j0.05 For transformers, assume Z' =…

A:

Q: to an A 3-phase, 11 kV, 20 MVA generator is connected 11 KV line. The positive, negative and Zero…

A: In this question we need to find the fault current, fault level and phase voltage at fault point for…

Q: A three-phase, Y-connected, 75-MVA, 27-kV synchronous generator has a synchronous reactance of 9.0 2…

A: The given data is shown below:

Q: Q5 An 11 kV three-phase 5 MVA, star-connected generator is protected by an earth- fault relay having…

A:

Q: For the radial power system shown in Figure 3, calculate the line-to-ground fault current flowing in…

A: Apply KVL to find I1.Ps Z42 I1 + Z23 I1 + Z34 I1 – 1(angle 0) = 0 (Z42 + Z23 + Z34) I1 = 1(angle 0)…

Q: jX, (1) 2 3x. iX; E, O E. Figure 1

A: Three phase short circuit occur at bus 2 a) Calculating sub transient generator current Ig…

Q: 2. for the system shown in figure. When Three phase to ground bolted Short Circuit Occurs on line 2.…

A: Step 1: Step 2: Step 3: Step 4:

Q: symmetrical fault occurs in the terminals of the synchronous generator. Find the direct axis…

A: Find the symmetrical fault current  Total Reactance?  If the armature Reactance Xa 7.4ohm Leakage…

Q: b) A fault occurs at bus 2 of the network shown in Figure Q3. Pre-fault nodal voltages throughout…

A:

Q: Assigning R3 as the load, find the following: R₁ ww 402 VS1 28V Question 6 R₂: VTH 202 R₂ (Load)…

A:

Q: Three 11 kV; 20 MVA 3 plase synchronous generators are connected to common set of bus bars. Each…

A: Given V=11 kV S=20 MVA X1 =20 % X2=15 % X3 =30 %

Q: As shown in Figure 1, a synchronous generator and motor are rated 100 MVA, 13.8 kV.??"=0.2per unit,…

A:

Q: Figure 1 shows a three-bus power system network of an electric utility company with each generator…

A: The one-line diagram of a three-bus power system network is given. The parameters (reactances) are…

Q: Q1. The following figure shows the power transformer differential protection with AY connection with…

A: The given circuit diagram is shown below:

Fault Analysis

In an electrical engineering system, a fault is an abnormal electric current flowing through the system, and fault analysis is the study of these faults. For instance, a short-circuit is a fault where the live wire touches the ground or neutral wire. If a circuit is interrupted by a failure of a current-carrying wire then an open circuit fault occurs. The open-circuit faults are also called series faults. One or more phases or ground may be involved in a three-phase fault or may occur only between two phases. Current flows into the earth in case of a ground fault or earth fault. For most situations, the prospective short circuit current of a fault that is predictable can be calculated. To limit the loss of service because of a failure, the protective devices can detect fault conditions and operate circuit breakers and also other devices. All phases equally can be affected in a poly-phase system which is known as symmetric electrical fault. The asymmetric fault becomes more complicated to analyze if only some phases are affected. By using methods such as symmetrical components, the power system analysis of these types of faults is often simplified. The main objective of power system protection is to design, detect, and interrupt power system faults.