The stress-strain diagram for a steel alloy having an original diameter of 0.5 in. and a gage length of 2 in. is given in the figure. Determine approximately the modulus of elasticity for the material, the load on the specimen that causes yielding, and the ultimate load the specimen will support. o (ksi) 80 70 60 50 40 30 20 10 e (in./in.) 0.04 0.08 0.12 0.16 0.20 0.24 0.28 0 .0.0005 0.001 0.0015 0.002 0.0025 0.0030.0035

The stress-strain diagram for a steel alloy having an original diameter of 0.5 in. and a gage length of 2 in. is given in the figure. Determine approximately the modulus of elasticity for the material, the load on the specimen that causes yielding, and the ultimate load the specimen will support. o (ksi) 80 70 60 50 40 30 20 10 e (in./in.) 0.04 0.08 0.12 0.16 0.20 0.24 0.28 0 .0.0005 0.001 0.0015 0.002 0.0025 0.0030.0035

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The stress-strain diagram for polyethylene, which is used to sheath coaxial cables, is determined from testing a specimen that has a gage length of 11 in. A load P on the specimen develops a strain of € = 0.024 in. /in. (Figure 1) Figure σ (ksi) 5 4 3 2 1 O = 3,7 e O 0.008 0.016 0.024 0.032 0.040 0.048 0.004 1 of 1 P € (in./in.) Part A Determine the approximate length of the specimen, measured between the gage points, when the load is removed. Assume the specimen recovers elastically. Express your answer in inches to four significant figures. 15] ΑΣΦ | 11 | vec L = Submit Provide Feedback Request Answer www ? Review in. Next >
σ (MPa) 490 0.007 -e (mm/mm) A specimen has the stress-strain diagram shown. The specimen has an original diameter of 12.4 mm, and its modulus of rigidity is 27.4 GPa. Determine the specimen's diameter when the longitudinal stress is 325 MPa.
a=2 b=5
Don't waste my question please, thank you god bless. I will vote it up if you give the solution.
A 1.6 ft long rod is made from the material, having the elastic modulus of E = 176 ksi and the yield strength of Sy = 1.04 ksi. The material has the stress-strain curve shown below. 1600 1400 1200 2 1000 800 600 400 200 0.5 1 1.5 Strain, percent By what amount must the rod be stretched from its original length for it to begin yielding? (Express your answer using whole numbers.) AL = mils Stress, psi
A strain gauges system mounted at a point on a structural member that is subjected to a multiaxial stress, where we have the following readings: &x = 7.820 x10+; Ey = -8.680x10¹4;&z= 3.200 x104; Vxy = 2.112 x10-³; Determine the stress components if the member is made of an isotropic material with linear elastic behavior having the following elastic properties: Poisson's ratio y = 0.32 and shear modulus G = 37.9 Gpa; E= Ox= Gy = Txy = 27.1 GPa 75 MPa 77 GPa 80 MPa -50 MPa 75 MPa -50 MPa 100 MPa 100 GPa 100 MPa 40 MPa 40 MPa 40 MPa -50 MPa 80 MPa
The steel strip has a uniform thickness of 50 mm. Compute the elongation of the strip caused by the 500-kN axial force. The modulus of elasticity of steel is 200 GPa. 1000 mm- 1000 mm 500 kN 500 kN 50 mm -120 mm 50 mm Match each item to a choice: Choices: # 1.345 mm # 1.356 mm # 0.6725 mm #0.678 mm 1.251 mm # 0.6253 mm
The elastic portion of the stress–strain diagram for an aluminum alloy is shown in the figure. The specimen from which it was obtained has an original diameter of 12.7 mm andagagelengthof50.8mm.IfaloadofP=60kNisapplied to the specimen, determine its new diameter and length. Take n = 0.35.
Answer question Q1
2) The elastic portion of the tension stress-strain diagram for an aluminum alloy is shown in the figure. The specimen used for the test has a gauge length of 50 mm and a diameter of 12.5 mm. When the applied load is 45 KN, the new diameter of the specimen is 12.48375 mm. Compute the shear modulus (Gal) for the aluminum. σ (MPa) 500 71 0.00614 € (mm/mm)
Determine the elastic modulus and the yield strength for the material having the stress-strain curve shown. Use the 0.2% offset method. 1600 1400 1200 E 1000 800 600 400 200 0.5 1 1.5 2 Strain, percent Elastic modulus: (Express your answer in whole numbers.) E = ksi Yield strength: (Express your answer using three significant figures.) Sy = ksi Stress, psi
8-11. A specimen is originally 300 mm long, has a diameter of 12 mm, and is subjected to a force of 2.5 kN. When the force is increased from 2.5 kN to 9 kN, the specimen elongates 0.225 mm. Determine the modulus of elasticity for the material if it remains linear elastic. a (MPa) 31.50 26.25 21.00 15.75 10.50 625 N 5.25 « (mm/mm) 0.05 010