8-11. A specimen is originally 300 mm long, has a diameterof 12 mm, and is subjected to a force of 2.5 kN. When theforce is increased from 2.5 kN to 9 kN, the specimenelongates 0.225 mm. Determine the modulus of elasticityfor the material if it remains linear elastic.a (MPa)31.5026.2521.0015.7510.50625 N5.25« (mm/mm)0.05010

Given Applied load = 2.5 kN Maximum Load = 9 kN Length of specimen = 300mm Elongation = 0.225 mm To…

Answered: 8-11. A specimen is originally 300 mm…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A specimen is originally 300 mm long, has a diameter of 14 mm, and is subjected to a force of 2.5 kN. When the force is increased from 2.5 kN to 7.5 kN, the specimen elongates 0.205 mm Part A Determine the modulus of elasticity for the material if it remains linear elastic. Express your answer to three significant figures and include the appropriate units. HẢ ? Value GPa E = Submit Request Answer Provide Feedback
A square bar subjected to a tensile load of 100KN having a gauge length of 200mm, extends to a length of 0.19mm. Given the tensile strength as 200 MPa, determine, (i) Side of the bar (express in mm) (ii) Final length (express in mm) (ii) Modulus of elasticity (express in GPa)
2) The elastic portion of the tension stress-strain diagram for an aluminum alloy is shown in the figure. The specimen used for the test has a gauge length of 50 mm and a diameter of 12.5 mm. When the applied load is 45 KN, the new diameter of the specimen is 12.48375 mm. Compute the shear modulus (Gal) for the aluminum. σ (MPa) 500 71 0.00614 € (mm/mm)
Determine the elastic modulus and the yield strength for the material having the stress-strain curve shown. Use the 0.2% offset method. 1600 1400 1200 E 1000 800 600 400 200 0.5 1 1.5 2 Strain, percent Elastic modulus: (Express your answer in whole numbers.) E = ksi Yield strength: (Express your answer using three significant figures.) Sy = ksi Stress, psi
Answer should be in MPa
A specimen with a length of 50 mm, width of 20 mm and thickness of 5 mm is subjected to a tensile test and the results obtained are given below. Determine the ultimate tensile strength of the specimen.
A= A specimen of magnesium having a rectangular cross section of dimension 3.2)mm x 19.1/mm and a gauge length of 63.5 is pulled in tension. Use the load-clongation characteristics tabulated as follows to: Load 0.0 1.38 2.78 5.63 7.43 8.14 9.87 12.85 14.10 14.34 13.83 12.59 6.99 (KN) Al 0.0 0.03 0.06 0.12 0.20 0.25 0.64 1.91 3,18 4.45 5.72 (mm) a) Plot the data as engineering stress versus engineering strain. b) Compute the modulus of elasticity.-M. L. 445010 c) Determine the tensile strength of this alloy.
a) A thin strip of rubber-like material has an unstretched length of 345 mm.i. If it is stretched around a pipe having an outer diameter of 112 mm, determine the average normal strain in the strip, assuming linear elastic behaviour. (3 marks)ii. A steel wire of diameter dwire = 1.5 mm also has an initial length of 345 mm. The Young’s Modulus of the steel material is 190 GPa and its yield strength is 275 MPa. What is the maximum pipe diameter that the wire can be stretched around without yielding and what is the magnitude of the tensile force in the wire for this elongation? Give your answers to two decimal places
Choose the correct option
A bar has a length of 200 mm and cross-sectional area of 7500mm^2. Determine the modulus of elasticity of the material if it is subjected to an axial tensile load of 50 kN and stretches 0.075 mm. The material has linear-elastic behavior.
Data taken from a stress-strain test for a ceramic are given in the table. The curve is linear between the origin and the first point. Plot the diagram, and determine the modulus of elasticity and the modulus of resilience.
Determine the elongation of an aluminium hollow cylinder of an inner diameter of 1.1 cm & the external diameter of 22.7 mm is subjected to an elastic tensile load of 271 kN. Take the elastic modulus of the aluminum specimen as 73 GPa and the initial length of the hollow cylinder as 186 mm. Solution: i) Cross-sectional Area (in mm2) = ii) Stress-induced (in N/mm2) = iii) Strain-induced (at least 3 decimal places accuracy)= iv) Elongation (in mm) =

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS